TY - JOUR ID - TI - Investigation of fatigue life of 6061-T6 aluminum alloys welded by metal inert gas welding دراسة عمر الكلال لسبيكة الالمنيوم (6061-T6) الملحومة بطريقة الغاز الخامل (MIG) AU - Nawres Jabar Nasser نورس جبار ناصر PY - 2015 VL - 19 IS - 3 SP - 1 EP - 15 JO - Journal of Engineering and Sustainable Development (JEASD) مجلة الهندسة والتنمية المستدامة SN - 25200917 25200925 AB - The present research aims to investigate the effects of Metal Inert Gas (MIG) welding process on the mechanical properties and fatigue life of AA 6061 T6. A series of experimental techniques has been conducted to evaluate the mechanical and fatigue life. metal inert gas (MIG) have been carried out on Rolled sheet of 12mm thickness to obtain many butt welding joints with dimensions of (200 *100* 12) mm and with geometry of single and double V at (70⁰) and square using ER- 5356 as a filler metal and argon as shielding gas. The welded pieces were tested by X-ray radiography and Faulty pieces were excluded Welding joints were subjected to heat treatment including heating the joints in furnace to (150 °C) for one hour then air cooling to relief heating stress.All specimens subjected to Vickers hardness, tensile test and microstructure examination. The examinations were carried out to show the effect of MIG weld method on the joint microstructure. The fatigue test of the welds and base alloy were examined to obtain the S-N curve.Results showed a general decay of mechanical properties of MIG weld joint that is due to heat input during the welding process and low cooling rate.

يهدف البحث الى بيان تاثير لحام القوس الكهربائي المحمي بالغازMIG على الخواص الميكانيكية ومقاومة الكلال لسبيكة المنيوم 6061 T6. تم استخدام صفيحتين من المعدن في لحام عدة وصلات تناكبية بالابعاد mm (200*100*12) بعد عمل زاوية لحام تحضيرية من جهة واحدة ومن جهتين مقدارها (70) درجة على شكل حرف (V) وبدون زاوية باستخدام سلك لحام 5356 والاركون كغار حماية .بعد عملية اللحام والتاكد من خلو الوصلة من العيوب من خلال فحصها بواسطة جهاز X-ray radiographyاجريت معاملة حرارية تضمنت تسخين الوصلة في فرن كهربائي عند درجة حرارة (°C 150) لمدة ساعة ثم التبريد بالهواء بهدف ازالة اجهادات اللحام اجري اختبار صلادة عيانية ومكروية بطريقة فيكرز واختبار شد وفحص البنية المجهرية لبيان تأثير اللحام على الخواص الميكانيكية وطبق اختبار الكلال للحصول على منحني العمر.أظهرت النتائج تدنيا في الخواص الميكانيكية للعينات الملحومة مقارنة بالمعدن الاساس للخواص الميكانيكية بسبب كمية الحرارة الداخلة والتبريد البطئ. ER -