TY - JOUR ID - TI - The Effect of Mold Rotational Speed on Mechanical Properties of Functionally Graded Polymeric Matrix Composites تأثير سرعة دوران القالب في الخواص الميكانيكية لمواد متراكبة بوليميرية متدرجة وظيفياً AU - Ahmed Akram Abdullah أحمد أكرم عبد الله AU - Awad Hallosh Khidhir عواد هلوش خضر PY - 2015 VL - 23 IS - 2 SP - 1 EP - 12 JO - AL-Rafidain Engineering Journal (AREJ) مجلة هندسة الرافدين SN - 18130526 22201270 AB - In this research, a functionally graded polymeric matrix composites (FGPMCs) were produced using centrifugal casting method. These composites were fabricated from unsaturated polyester resin as a matrix and reinforced with silicon carbide particles (SiCp) of (106µm) and (6%)bulk volume fraction, using different mold rotational speeds(400,500,600 R.P.M) at room temperature (22Cº).Additional (3) samples of pure polyester were manufactured at the same conditions for comparison purpose .The aim of the present research was to study the effect of mold rotational speed on local values of volume fraction,hardness and Young modulus at specific points along the graded samples. Hardness was measured at these points then graded samples were cut to eight portions .Densityand volume fraction were evaluated,then standard homogenoussamples of constant but different volume fraction were manufactured. Results shows that local values of volume fraction, hardness and Young Modulus decreased in nearby positions of the center of rotation and increased in positions far away from the center of rotation with increasing mold rotational speed.

تم في هذا البحث انتاج مواد متراكبة بوليميرية متدرجة وظيفياً(FGPCs) مادتها الاساس من البولي استر غير المشبع(Unsaturated Polyester Resin) ومعززة بدقائق من كربيد السليكون(SiCp) بكسر حجمي كلي (%6) وحجم حبيبي(106µm) ومصنعة بطريقة الطرد المركزي وبسرعة دورانية مختلفة (400,500,600R.P.M) وبدرجة حرارة الغرفة(22Cº) فضلا عن انتاج ثلاثة نماذج من البولي استر النقي وبالظروف نفسها لغرض المقارنة. تم دراسة تأثير تغير سرعة دوران القالب في القيم الموضعية للكسر الحجمي والصلادة ومعامل المرونة للنماذج المصنعة وفي نقاط محددة على طول كل أنموذج متدرج .تم قياس الصلادة في هذه النقاط ومن ثم تقطيع كل انموذج متدرج الى ثمانية قطع وحساب كثافتها وتحديد كسرها الحجمي وانتاج نماذج متجانسة قياسية ذات مواصفات مناظرة لتلك الخصائص لغرض اختبار الشد .اظهرت نتائج البحث انخفاض القيم الموضعيةللكسرالحجمي والصلادة ومعامل المرونة في المواضع القريبة من مركز دوران القالب وارتفاع هذه القيم في المواضع البعيدة عن مركز دوران قالب الطرد المركزيمع زيادة سرعة دوران القالب. ER -