TY - JOUR ID - TI - The effect of shot peening on the notch sensitivity factor and Neuber characteristic length for 7075-T6 Aluminum alloy تأثير سفع الكرات على معامل حساسية الحز و الطول الخصائصي لنيبر لسبيكة الالمنيوم (7075-T6) AU - Ahmed Naef Ibrahim Al-Khazraji* أحمد نايف أبراهيم الخزرجي AU - Thamer Amoori Hashim AL-Taie ثامر أموري هاشم الطائي PY - 2015 VL - 19 IS - 4 SP - 200 EP - 216 JO - Journal of Engineering and Sustainable Development (JEASD) مجلة الهندسة والتنمية المستدامة SN - 25200917 25200925 AB - This paper has been studied the effect of shot peening to improve the mechanical properties, especially the enhancement of fatigue life, also to study the effect of shot peening on notch sensitivity factor (q) for two kinds of notched circular cross-sectional area of (AA7075-T6) with radii of notches (1, 1.25 mm). Due to the dimensions of specimens and notch radius, the stresses concentration factors 〖(K〗_t) were (1.62, 1.73), respectively. This paper was included the effect of compressive residual stresses on the Neuber characteristic length (ρ).The experiments of shot peening were carried out at two different shot peening times (SPT) (0, 8, 10, 12, 20 min). The tensile test after shot peening was done to know the improvement in mechanical properties, The surface roughness, microhardness, and the compressive residual stresses by X-ray diffraction (XRD) were measured. The results showed the maximum decreasing in notch sensitivity factor (22.35 %) and maximum increasing in Neuber characteristic length which was (270.2%) at the same shot peening time (10 min) and notch radius (1.25 mm).

في هذا البحث تم دراسة تأثير السفع بالكرات على تحسين الخواص الميكانيكية و خاصة تحسين حد الكلال و تأثيره على معامل حساسية الحز(q) لعينات من سبيكة الالمنيوم (AA7075-T6) دائرية المقطع , لحالتين من الحز بأنصاف أقطار (1, 1.25) ملم , تم تحديد معامل تركيز الاجهاد (K_t)(1.62, 1.73) بالاعتماد على ابعاد العينة والحز وكذلك تأثير حد الكلال على الطول الخصائصي لنيبر (ρ).تم اجراء التجارب للسفع لزمنيين مختلفين هما (10, 20) دقيقة . بعد ذلك تم أجراء فحوصات الشد, الخشونة السطحية, الصلادة الميكروية و الاجهادات المتخلفة الضغطية بطريقة حيود الاشعة السينية (XRD) أظهرت النتائج حدوث اعلى نقصان في معامل حساسية الحز و اعلى زيادة في الطول الخصائصي لنيبر وذلك عند حالة السفع بزمن (10) دقيقة مقارنة بالمعدن قبل عملية السفع . حيث بلغ اعلى نقصان لمعامل حساسية الحز بنسبة (22.35%) واعلى زيادة بالطول الخصائصي لنيبر (%270.2) عند نصف قطر حز (1.25) ملم. ER -