@Article{, title={STUDY THE EFFECT OF SILICA (SIO2) PARTICLES ADDITIONS ON THE WEAR RESISTANCE OF ALUMINUM BIASED ALLOYS (AL-6061, AL-5086) دراسة تاثير اضافة دقائق السليكا (SiO2) على مقاومة البلى لمواد متراكبة ذات اساس من سبيكة الالمنيوم (Al-6061 وAl-5086).}, author={Yasir Muhi Abdulsahib ياسر محي عبدالصاحب}, journal={DIYALA JOURNAL OF ENGINEERING SCIENCES مجلة ديالى للعلوم الهندسية}, volume={8}, number={3}, pages={8-19}, year={2015}, abstract={Aluminum matrix composite is most important materials used in various industries because of its good properties such as wear resistance, low density, and high resistance to weight ratio. In this paper, Metal matrix composites (MMCs) of the base alloy (Al-6061) and (Al-5086) reinforced by silica particles (SiO2) (1.5, 3, and 4.5 wt%) with particles size (150 µm) was prepared by stir casting using vortex technique, silica particles (SiO2) are added to the molten and then stirred the melt by electrical mixer stir to work the vortex and then pour the mixture molten into cylindrical mold and then was cutting and preparation of samples for examination and testing of wear, hardness, density and study the microstructure of the samples and the comparison between them. Results show from this study that the wear resistance of Al matrix composite its improvement due to addition of silica particles (SiO2) as compared with basis alloys, (Al-5086) matrix composite has higher wear resistance rather than (Al-6061) matrix composite. The higher wear resistance at added the 4.5 wt.% of silica (SiO2). The addition of silica particles in proportions above has contributed to the improvement of hardness which is reflected in improved wear resistance, and that this improvement in properties increases with the proportion of silica particles added to alloys base. As for the properties of density, decreases the density of Al-matrix composites as compared with base alloys with low proportion when added the silica particles (SiO2).

تعد المواد المتراكبة ذات اساس المنيوم من اهم المواد التي تدخل في مختلف الصناعات بسبب ماتملكه من خصائص جيدة مثل مقاومة البلى, الكثافة الواطئة, والمقاومة العالية نسبة الى الوزن. تم في هذا البحث تحضير مواد متراكبة ذات اساس من سبيكة المنيوم (Al-6061) و (Al-5086) مقواة بدقائق السليكا (SiO2) وبنسبة وزنية (1.5%، 3%، 4.5%) وبحجم حبيبي مقداره (150 مايكرون). المواد المتراكبة حضرت بطريقة الدوامة (Vortex method)، حيث تم اضافة دقائق السليكا (SiO2) الى المنصهر ثم الخلط بواسطة خلاط كهربائي لعمل الدوامة ثم صب الخليط المنصهر في قالب معدني اسطواني, بعد ذلك تم تقطيع وتحضير العينات لاجراء فحص واختبار البلى, الصلادة، الكثافة ودراسة التركيب المجهري للنماذج والمقارنة بينهما. تبین من النتائج التي تم الحصول علیها من خلال هذه الدراسة ان مقاومة البلى للمواد المتراكبة قد تحسنت نتیجة إضافة دقائق السليكا (SiO2) مقارنة مع السبیكة الاساس وكانت مقاومة البلى للمواد المتراكبة ذات اساس (Al-5086) اعلى من مقاومة البلى للمواد المتراكبة ذات اساس (Al-6061). وقد تم الحصول على اعلى مقاومة بلى عند نسبة اضافة 4.5% من دقائق السليكا (SiO2). ان اضافة دقائق السليكا بالنسب اعلاه قد ساهم في تحسن قيم الصلادة مما انعكس على تحسن مقاومة البلى، وان هذا التحسن في الخواص یزداد بزیادة نسبة إضافة دقائق السليكا للسبیكة الاساس. اما بالنسبة الى خاصية الكثافة, فقد قلت قيمها للمواد المتراكبة بالنسبة الى السبيكة الاساس وبنسبة قليلة عند اضافة دقائق التقوية السليكا (SiO2).} }