@Article{, title={Experimental and Simulation Study the Effect of Different Reduction Ratios in Cold Rolling Process on the Residual Stresses of AL 2024 Alloy دراسة تجريبية ومحاكاة تأثير نسب تخفيض مختلفة في عملية الدرفلة الباردة على الاجهادات المتبقية لسبيكة المنيوم 2024}, author={Samir Ali Amin Al-Rabii and Sadiq Jaffar Aziz and Ali Hussein Alwan}, journal={Engineering and Technology Journal مجلة الهندسة والتكنولوجيا}, volume={33}, number={5 Part (A) Engineering}, pages={1049-1064}, year={2015}, abstract={Cold forming processes are the common processes in sheet metal forming, especially in the final stages of production processes. In this work, cold rolling process was selected to study the effect of different reduction ratios on the residual stresses state in aluminum alloy (2024). Sheets of aluminum alloy (2024-T3) were prepared with dimensions (400 X 80 X 3.15 mm).The annealing process was conducted for these sheets to get the temper condition (2024-O). The cold rolling process was performed with different reduction ratios (10%, 20%, 30%, 40%, 50%, 60%) by a rolling machine composed of two rolls having (50 mm) diameter each.The residual stresses were measured using X-ray diffraction technique (XRD) in two directions (rolling direction RD, and transverse direction TD).The results of X-ray diffraction showed the presence of residual stresses at the surface of rolled specimens, and these were compressive stresses in the two tested directions (RD, and TD) at 10% reduction ratio. When the reduction ratio exceeded 10%, these stresses transformed to tensile stresses for specimens tested in rolling direction, while these stresses remained compressive type for all reduction ratios in transverse direction.Computer simulation was carried out using finite element method (FEM) by (ANSYS-LSDYNA 12.1) software to investigate the residual stresses behavior of AA 2024. The numerical results showed a good agreement with the experimental resultsespecially for samples tested in the rolling direction.

تعد عمليات التشكيل على البارد من العمليات الشائعة في تشكيل الالواح المعدنية وخصوصاً في المراحل النهائية من عمليات الانتاج. في هذا البحث تم اختيار عملية الدرفلة الباردة للتحقق من تأثير نسب التخفيض المختلفة على حالة الاجهادات المتبقية لسبيكة المنيوم (2024). تم تهيئة الواح من سبيكة المنيوم (2024-T3) بأبعاد(400 X 80 X mm3.15). أجريت عملية التلدين لهذه الالواح للحصول على ((2024-O temper. تم اجراء عملية الدرفلة على البارد بنسب تخفيض مختلفة (60%, 50%, 40%, 30%, 20%, 10%) بواسطة ماكنة درفلة متكونة من درفيلين قطر كل منها(50 mm). تم قياس الاجهادات المتبقية باستخدام تقنية حيود الأشعة السينية وباتجاهيين (اتجاه الدرفلة, والاتجاه المستعرض). أظهرت نتائج حيود الاشعة السينية وجود أجهادات متبقية على سطح العينات المدرفلة وكانت هذه الاجهادات ضغطية بالاتجاهيين (اتجاه الدرفلة, والاتجاه المستعرض) عند نسبة تخفيض 10 %.عندما تجاوزت نسبة التخفيض %10 هذه الاجهادات تحولت الى اجهادات شدية للعينات المختبرة باتجاه الدرفلة, في حين بقيت هذه الاجهادات ضغطية لجميع نسب التخفيض بالاتجاه المستعرض. تم أجراء محاكاة حاسوبية لعملية الدرفلة الباردة بأستخدام طريقة العناصر المحددة ببرنامج (ANSYS LS-DYNA 12.1) للتحقق من سلوك الاجهادات المتبقية لسبيكة الالمنيوم 2024. بينت النتائج العددية توافق جيد مع الجانب العملي, وخصوصاً للعينات المفحوصة بأتجاه الدرفلة.} }