@Article{, title={Torsional Resistance of Reinforced Concrete Girders with Web Openings مقاومة اللي للأعتاب الخرسانية المسلحة حاوية على فتحات وترة}, author={Mohannad Hussain Al-Sherrawi مهند حسين الشراوي and Zainab Muthana Shanshal زينب مثنى شنشل}, journal={Journal of Engineering مجلة الهندسة}, volume={22}, number={2}, pages={137-155}, year={2016}, abstract={In this study, a three dimensional finite element analysis was utilized to study the behavior of reinforced concrete T-girders with and without web openings under pure torsion by using ANSYS APDL 15.0 program. Fourteen reinforce concrete T- girders were analyzed; one of the girders (without web openings) was modeled as a control girder. The analysis variables considered for the other girders are: size, shape, position of web openings, number of web openings and the method was used to strengthen the member at openings, (using internal deformed steel bars as in the case where the openings are planned before casting the girders). To study the general behavior of finite element models, torque-angle of twist plots at the end of the span near the loaded arms were represented. From this relation, it was showed a decreasing in the strength of the T-girders with web openings under the torsional loads and increasing of the angle of twist. The results were analyzed in terms of torque twist characteristics; ultimate torque, crack patterns, crack width, warping and stresses. These terms were presented and a comparison between the finite element results was made.

تم من خلال هذا البحث دراسة سلوك العتبات الخرسانية المسلحة لعتبات بشكل T الحاوية على فتحات وعتبات بدون فتحات تحت تأثير عزم اللي الصرف; تمت نمذجة العتبات بأستخدام طريقة العناصر المحددة لنماذج ذات ابعاد ثلاثية بأستخدام برنامج ANSYS APDL 15.0، حيث تم تحليل اربعة عشر نموذج احدها بدون فتحه والذي يعتبر النموذج المصدري حيث تم مقارنة نتائج بقية النماذج معه. المتغيرات التي تم استخدامها عند دراسة المقارنة مع االنماذج الأخرى هي: حجم وشكل وموقع وعدد الفتحات المستخدمة وطريقة تقوية الفتحات التي تتم بأستخدام تسليح داخلي حول الفتحات عند التصميم. ولأجل دراسة العلاقات المتعلقة بالنماذج والمصممة بطريقة العناصر المحددة, كالعلاقة بين عزم اللي الصرف وزاوية الألتواء والتي تم قياسها عند نهاية مقطع العتبة القريبة من الذراع الذي يسلط عليه الأحمال, وبشكل عام ومن خلال هذة الدراسة وجد تناقص في مقاومة العتبات لعزوم اللي الصرف وزيادة في مقدار زاوية عزم الألتواء عند وجود الفتحات .و تمت ايضا دراسة نتائج حساب اقصى عزم التواء وشكل وسمك التشققات ودراسة الأنحناءات والأجهادات وتم اجراء مقارنة فيما بينها.} }