TY - JOUR ID - TI - The Influence of Quenching Media and Aging Time on Microstructure and Mechanical Behavior of 6061 Aluminum Alloy تأثير أوساط الاخماد وزمن التعتيق على التركيب المجهري والسلوك الميكانيكي لسبائك المنيوم 6061 AU - Naser Korde Zedin PY - 2015 VL - 33 IS - 8 Part (A) Engineering SP - 1757 EP - 1770 JO - Engineering and Technology Journal مجلة الهندسة والتكنولوجيا SN - 16816900 24120758 AB - Aluminum-magnesium-silicon (Al-Mg-Si) alloys are medium strength, excellent formability, good corrosion resistance and widely used in extruded products and automotive body materials. The influence of quenching media with different aging time on microstructure and mechanical properties of 6061 aluminum alloy was investigated. The results show formation of (Mg2Si) and (CuAl2) phaseswhensolution treatmentwas applied (at 520°C for 2h,followed by quenching in water and oil at room temperature then aging (at 175°C for 2, 4and6h)) which resultimprovingof both the strength, hardness and decreases elongation. It can be noted that, the grains of samples which are quenching in water is finer than the structure of samples which are quenching in oil. The values of yield stress and ultimate tensile strength decrease respectively with increasing aging time to 6h as (258MPa) and (264MPa) for water quenching and (199MPa) and (235MPa) for oil quenching. In this piper were measured and discussedthe variation of the yield stress, ultimate tensile strength and elongation with different solution quenching and aging time.

تمتاز سبائك (Al-Mg-Si) بمقاومتها المتوسطة وقابليتها العالية للتشكيل ومقاومتها الجيده للتاكل مما جعلها واسعة الانتشار في صناعة المبثوقات وهياكل وسائط النقل. في هذا البحث تم دراسة تأثير اختلاف أوساط الاخماد و زمن تعتيق على البنية المجهرية و الخواص الميكانيكية لسبائك المنيوم 6061. بينت النتائج تكون طوري Mg2Si و CuAl2عند اجراء المعالجة المحلولية (بدرجة حرارة 520مͦلمدة(2ساعة) والمتبوعة بالاخماد (مرة بالماء و مرة بالزيت) عند درجة حرارة الغرفة ثم التعتيق عند درجة حرارية 175 مͦلمدة (6,4,2ساعة) مما ينتج تحسين في كلاً من المقاومة و الصلادة وتنخفض المطيلية. كذلك نلاحظ ان البنية المجهرية للعينات التي يتم اخمادها بالماء اصغر من البنية المجهرية للعينات التي يتم اخمادها بالزيت. قيم اجهاد الخضوع ومقاومة الشد القصوى التي تم الحصول عليها تقل بزيادة زمن التعتيق الى 6 ساعة ,القيم بالتتابع (258 ميكا باسكال) و(264 ميكا باسكال) للاخماد بالماء و (199 ميكا باسكال) و(235 ميكا باسكال) للاخماد بالزيت. في هذا البحثتم قياس و دراسة التغيرات التي تحدث على المعادن بواسطة دراسة مقاومة الخضوع ومقاومة الشد والمطيلية مع اختلاف محاليل الاخماد و زمن التعتيق. ER -