TY - JOUR ID - TI - The Study of the Release Mechanism of TiO2 Nanotubes-NP Conjugate Using Polymer Encapsulate as a Drug Delivery System AU - Asma Hadi Mohammed AU - Basim M. Hasan AU - Wisam Khadom Al-Hashimy AU - Majid Shannon Khalaf PY - 2016 VL - 19 IS - 2 SP - 1 EP - 7 JO - Al-Nahrain Journal of Science مجلة النهرين للعلوم SN - 26635453 26635461 AB - TiO2 nanotube array was fabricated by anodisation technique of a pure titanium plate. The anodisation process was carried out in ammonium fluoride/ ethylene glycol electrolyte, the applied voltage was 60 volt. The average length and diameter of the nanotubes were 12 µm and 80 nm respectively. After annealing of TiO2 nanotubes at 500°C for 3h, the amorphous nanotubes walls converted into anatase phase. The TiO2 nanotubes array material was employed as container for methylene blue (MB) solution. Another layer (container for MB) was created then when TiO2 coated with nanoparticles (NP) in order to compare the release mechanism with TiO2 nanotubes. The aim was to develop an additional control of chemical release kinetics polyvinyl alcohol (PVA) which was used to encapsulate the surface of the loaded TiO2 nanotubes and TiO2 nanotubes-NP conjugate. The results showed that the release mechanism can be controlled more efficiently by using nanotubes-NP conjugate rather than using single layer of TiO2 nanotubes only. The morphology of the arrays was characterized by X-ray diffraction (XRD), Transmission Electron Microscopy (TEM) and Scanning Electron Microscopy (SEM).

تضمن البحث تكوين انابيب ثاني أوكسيد التيتانيوم النانوية على معدن التيتانيوم Ti. محلول الانودة الكهروكيميائية مكون من فلوريد الأمونيوم (NH4F) مع اثيلين كلايكول ethylene glycol)) عند فولطية مسلطة مقدارها 60 volt . حيث كان معدل طول الانبوب12 µm and 80 nm تقريباً. بعد عملية التلدين الحراري لانابيب ثاني اوكسيد التيتانيوم عند درجة حرارة 500 °C خلال فترة زمنية مقدارها ثلاث ساعات تحولت جدران انابيب ثاني اوكسيد التيتانيوم غير المتبلورة الى طور anatase. في هذا البحث تم استخدام انابيب ثاني اوكسيد التيتانيوم كوعاء حاوي لمحلول methylene blue (MB). تم تكوين طبقات اخرى حاوية لل (MB) متولدة عند طلاء ثاني اوكسيد التيتانيوم بجسيمات نانوية لغرض المقارنة في حالة تحفيزها مع انابيب ثاني اوكسيد التيتانيوم. ان الهدف وضع سيطرة اضافية لحركية تحفيز الكيميائية لبوليمرpolyvinyl alcohol (PVA) المستخدم لتغليف سطح انابيب ثاني اوكسيد التيتانيوم المحملة وانابيب ثاني اوكسيد التيتانيوم والجسيمات النانوية. اظهرت النتائج الية التحفيز يمكن السيطرة عليها بكفاءة اعلى في حالة انابيب ثاني اوكسيد التيتانيوم اكثر من حالة استخدام انابيب ثاني اوكسيد التيتانيوم فقط. تم دراسة تركيب من خلال استخدام حيود الاشعة السينية, مجهر المسح الالكتروني ومجهر نفاذية الالكتروني. ER -