TY - JOUR ID - TI - Experimental Investigation of Jet Impingement Cooling On Ribbed Target Surface اختبار تجريبي لتبريد النفاثات الصدمية على سطح هدف مضلع AU - Ali K. Bayer AU - Assim. H. Yousif PY - 2016 VL - 34 IS - 2 Part (A) Engineering SP - 205 EP - 219 JO - Engineering and Technology Journal مجلة الهندسة والتكنولوجيا SN - 16816900 24120758 AB - Experimental investigation of jets impacting at right angleon a flat surfaceis introduced in the present study. Round jet holes of inline arrays arrangements with diameter (5mm) and jet to jet spacing of 4 jet hole diameter are considered. Jet Reynolds numbers of 4000 to 16000 and jet height to diameter ratio (space between the jet plate and target plate) of 2.0 is maintained. The heat transfer model consists of amultiple jet holes, ribbed target plate having back side resistive film. Threetarget models have been considered; model (1) is a clean surface target acting as the baseline case, the model (2) the target surface consists of lateral rib rows and model (3) the target surface consists grids rib arrangement. The ribs height for models (2 and 3) is 0.86 of jet diameter of the triangle shape. The average wall cooling effectiveness and heat transfer coefficients and consequently the Nusselt numbers for each model are estimated. Numerical computations of jets flow field are made.Theresults show that model (3) enhanced both heat transfer coefficients in the target plat inner surface and wall cooling effectiveness in the target plat outer surface greatly,the maximum increments in heat transfer coefficient and wall coolingeffectiveness are 14.5% and 4.5% respectively.

تم اجراء تجارب عملية للتبريد الصدمي النفثي بزاوية قائمة على سطح صفيحة الهدف المستوية . وقد كانت النفاثات عبارة عن ثقوب دائرية مرتبة على شكل صفوف تقع على خط واحد ذات قطر(5ملم) وكان البعد بين ثقب واخر هو 4 مرات قطر الثقب. وتراوحت قيم عدد رينولدز للثقوب من 4000 الى 16000 والمسافة بين صفيحة الهدف والثقوب هي مرتين من قطر الثقب. وكان النموذج العملي لعملية انتقال الحرارة هو نتيجة اصطدام عدد من النفاثات على سطح صفيحة مضلعة سطحها الخارجي ذو غشاء مقاوم. وتم اعتماد ثلاثة نماذج لاجراء التجارب: النموذج الاول هو الحالة الاساسية وهي صفيحة الهدف الخالية من الاضلاع والنموذج الثاني هو لصفيحة الهدف ذات الاضلاع العرضية والنموذج الثالث هو لصفيحة الهدف ذات الاضلاع الشبكية. كانت الاضلاع المستخدمة ذات شكل مثلث متساوي الاضلاع وكانت نسبة ارتفاعه الى قطر الثقب هي 0.86. تم حساب فعالية التبريد ومعامل انتقال الحرارة (عدد نسلت). واظهرت النتائج افضلية للنموذج الثالث في تحسين معامل انتقال الحرارة وكذلك فعالية التبريد وكانت اعلى نسبة للزيادة هي 14.5 % و4.5 % على التوالي. ER -