TY - JOUR ID - TI - Effect of Mixing Silanized Poly Propylene and Siwak Fibers on Some Physical and Mechanical Properties of Heat Cure Resin Denture Base تأثير إضافة خليط من ألياف البولي بروبيلين والسواك بعد المعالجة السطحية على بعض الخصائص الفيزيائية و الميكانيكية لقاعدة طقم من الأكريل الحراري AU - Hanan Abdul-Rahman Khalaf حنان عبد الرحمن خلف PY - 2016 VL - 16 IS - 1 SP - 26 EP - 37 JO - Al Mustansiriyah Journal for Pharmaceutical Sciences مجلة المستنصرية للعلوم الصيدلانية SN - 18150993 2959183x AB - PMMA is used in construction of denture base due to several advantages, including biocompatibility and optimal appearance. Operators and patients complain from fracture of acrylic denture base material attributed to decreased resistance to impact, flexural or fatigue stresses. The aim of the research is to assess the effect of addition of silanized mixture of siwak and poly propylene fibers on PMMA denture base.Fourteen acrylic resin specimens were prepared for each test (Impact strength, Transverse strength, Shear bond strength, Thermal conductivity, Shore D hardness, Surface roughness and Water sorption) the specimens were grouped as control group (n=7) :no fibers additive and experimental group (n=7):(2 %) silanized mixture of siwak and poly propylene fibers, 4 mm length, FT-IR was done to investigate the presence of functional groups of coupling agent (TMSPM) on the tested fibers, independent t-test was used for statistical analysis of the resulted data. Statistical analysis indicated that silanized mixture of poly propylene and natural fibers (siwak) produced significant increase (p≤0.05) of impact strength and highly significant increase (p≤0.01) of shear bond strength, transverse strength, thermal conductivity and shore D hardness of heat cure acrylic resin while a non significant increase (p>0.05) of surface roughness and water sorption properties was observed in comparison to non fiber reinforced resin specimens. The addition of silanized mixture of siwak and polypropylene fibers into heat cure PMMA improve the tested physical and mechanical properties.

يستخدم البولي مثيل ميثاكريليت في صناعة قاعدة أطقم الأسنان بسبب العديد من المزايا مثل التوافق الحيوي مع الأنسجة والمنظر الجميل الأمثل ولكن المرضى يعانون من كسر طقم الأكريلك بسبب إنخفاض المقاومة للصدمة وللقوة العرضية.الهدف من هذه الدراسة هو تقييم إضافة خليط من ألياف البولي بروبيلين وألياف السواك الطبيعية المضادة للميكروبات على قاعدة طقم الأكريلك.تم إعداد أربعة عشر من عينات راتنج الأكريلك الحراري لكل من الإختبارات التالية: قوة الصدمة, قوة المستعرضة, التوصيل الحراري, الصلادة السطحية, خشونة السطح, قوة الالتصاق القصي لطقم الأسنان وقابلية إمتصاص الماء. تم تقسيم العينات الى مجموعة السيطرة (7 عينات) والمجموعة التجريبية (7 عينات) التي تحتوي على 2% من خليط الألياف المعالجة سطحيا وبطول 4 ملم وقد تم إجراء فحص FTIRللتحقق من وجود مادة silane على سطح الألياف وتم تحليل النتائج بواسطة إختبار t- test للتحليل الاحصائي للبيانات.أظهرت النتائج زيادة معنوية في قوة الصدمة, قوة المستعرضة, قوة الإلتصاق القصي لقاعدة الطقم, الصلادة والتوصيل الحراري لمادة راتنج الأكريلك الحراري المدعم بالألياف كما أظهرت النتائج إنخفاض غير معنوي في خشونة السطح وخاصية إمتصاص الماء عند المقارنة مع مجموعة السيطرة. نستنتج من هذه الدراسة أن إضافة خليط من ألياف البولي بروبيلين وألياف السواك المعالجة سطحيا يؤدي الى تحسين الخصائص الفيزيائية والميكانيكية لمادة راتنج الأكريلك. ER -