@Article{, title={EXTRUSION BEHAVIOR OF WROUGHT AND AS-CAST AL-5.5%ZN-2,5%MG ALLOY AT DIFFERENT TEMPERATURES AND REDUCTIONS USING SQUARE DIE ANGLE.}, author={Kadhim Mijbel Mashloosh}, journal={DIYALA JOURNAL OF ENGINEERING SCIENCES مجلة ديالى للعلوم الهندسية}, volume={9}, number={3}, pages={90-103}, year={2016}, abstract={Laboratory scale extrusion experiments were carried out on AA7075 billets. Two groups of wrought and homogenized as-cast (Ф 25 X 60) mm cylindrical billets were used. Each billet was cut longitudinally into halves, the two mating surfaces were polished and scribing an orthogonal network of furrows (0.1 mm wide and 0.3 mm deep) onto one of the faces. The network formed was as a square grid of 1 mm spacing. The two halves were put together and partially extruded, removed from the die, separated along the same plane and the grid distortions were observed.16 experiments were carried out on each group of wrought and as-cast billets. Each group 3 6 was extruded at four different pre-heating temperatures (350, 400, 420, and 450) oC. Four values (60, 70, 78, 95.6) % of percentage reduction in cross sectional area were used at each temperature. The ram speed was 4.6 mm/sec. A mixture of graphite powder and grease was 40 used as a lubricant.The usual type consisting of a single maximum in the transverse grid lines located at the extrusion axis was occurred in all the experiments of both groups.Microstructure tests were done on the other half after it has been extruded for all the billets of the two groups. Five positions were taken for the microstructure. The magnitude of the maximum load needed for the experiments was reported for both wrought and as-cast billets.

تم في هذا البحث اجراء تجارب بثق على مستوى مختبري لنماذج من سبيكة الالمنيوم نوع AA7075 و كانت النماذج عبارة عن عينات من السبيكة بحالتها الطروقة و نماذج أخرى من نفس السبيكة بعد عملية السباكة و اجراء معاملة حرارية عليها(معادلة).كانت النماذج المعدة لغرض البثق اسطوانية الشكل بابعاد(قطر25ملم و طول 60 ملم).تم قطع كل نموذج طوليا الى نصفين و تنعيم السطحين المقطوعين و صقلهما ثم عمل شبكة اخاديد صغيرة بسمك 0.1 ملم و عمق 0.3 ملم على احد النصفين وعلى شكل مربعات طول ضلعها 1 ملم .تم بثق العينة جزئيا بعد وضع النصفين على بعضهما و رفع العينة لدراسة التشوه الحاصل في الشبكة بعد البثق.تم اجراء 16 تجربة بثق على كل مجموعة من العينات الطروقة و المسبوكة مسبقة التسخين عند درجات حرارة(350,400,420,450oم) وكانت نسب التخفيض المئوية في مساحة المقطع هي (60,70,78,95%) عند كل درجة حرارة . سرعة البثق 4.6 م/ثا وباستخدام نوعين من المزيتات هما الكرافيت و الشحم (الزيت الصلب) لوحظ ان التشوه الطبيعي يحدث بقيمة عليا واحدة وعلى طول محور البثق ولمجموعتي التجارب . تم فحص التركيب المجهري للنصف الثاني للعينة وفي خمس مناطق كما تم تسجيل الحمل الأقصى المطلوب في كل حالة بثق للمطروقات والمسبوكات.} }