@Article{, title={Study the effect of annealing on the Structural and Optical properties of Copper oxide films prepared by Sol-Gel Spin Coating دراسة تأثير التلدين على الخواص التركيبية والبصرية لأوكسيد النحاس المحضر بطريقة الطلاء الدوراني (SOL-GEL)}, author={Thuraya yarb ثريا يعرب صبري and Riyadh sami رياض سامي عنتر and Ali saleh علي اسماعيل صالح}, journal={Tikrit Journal of Pure Science مجلة تكريت للعلوم الصرفة}, volume={21}, number={5}, pages={148-153}, year={2016}, abstract={This research is to study the effect of annealing on the structural and optical properties on the thin films copper oxide(CuO,Cu2O) was deposited on glass substrate by using technique Spin-Coating (Sol-Gel) with speed (3000 RPM) during the time of the deposition (30 sec). Was the preparation of the solution using a material of copper acetate (Cu(C2H3O2)2.H2O) as a basis and Diethanolamine (DEA) (C4H11NO2) as installed and Ethanol (C2H6O) as a solvent, the solution prepard at a concentration of 0.2M. The annealing at temperatures (250,350, 450,550)°C for one hour. We have investigated the Structural characteristics using (XRD and AFM) analyses ,from of (XRD) analyses show that the thin films are polycrystalline and annealing the films at 350 °C completely converts these films to tenorite structure with composition of CuO. And from (AFM) analyses show that the grian size increases with increasing annealing temperature. Either optical characteristics by spectroscopy UV in the range of wavelength (300-1100) nm. It is observed that the transmittance and allowed direct optical band gap of the films decreases with the increase of annealing temperature from 4.0 eV to 3.92 eV.

في هذا البحث تمت دراسة تأثير التلدين على الخواص التركيبية والبصرية لأغشية اوكسيد النحاس CuO,Cu2O)) المرسبة على قواعد من الزجاج باستخدام تقنية الطلاء الدوراني Sol-Gel)) وبسرعة (3000 RPM) خلال زمن ترسيب (30sec). حضر المحلول بأستخدام مادة خلات النحاس المائية (Cu(C2H3O2)2.H2O) كمادة اساس ومادة Diethanolamine (DEA) (C4H11NO2) كمادة مثبتة وكحول الايثانول (C2H6O) كمادة مذيبة وحضر المحلول بمولارية 0.2M . تم تلدين الاغشية بدرجات حرارة (250,350,450,550)°C لمدة ساعة واحدة. تم دراسة الخصائص التركيبية من خلال فحوصات XRD,AFM)), وخلال فحص(XRD) تبين ان الاغشية ذات تركيب متعدد التبلور وعند تلدين الغشاء بدرجة حرارة 350°C يتحول كليا الى تركيبCuO)) , ومن خلال فحص (AFM) تبين أن معدل الحجم الحبيبي يزداد بزيادة درجة حرارة التلدين, اما الخصائص البصرية تم فحصها بواسطة مطيافية الاشعة المرئية وفوق البنفسجية ضمن مدى الطول الموجي 300-1100)nm). ويلاحظ ان النفاذية وفجوة الطاقة البصرية للاغشية تقل بزيادة درجة حرارة التلدين من 4.0 eV الى 3.92 eV. .} }