@Article{, title={EFFECT OF WEB OPENING ON THE AXIAL LOAD CAPACITY OF STEEL COLUMNS WITH COLD FORMED THIN WALLED SECTION (CFS) تاثيروجود الفتحات في وترة المقاطع الفولاذية ذات الجدران النحيفة المشكلة على البارد على تحمل الاحمال المحورية للاعمدة الفولاذية}, author={Sadjad Amir Al-Jallad سجاد عامر حمزة الجلاد and Haitham Al-Thairy هيثم علي بادي الثائري}, journal={KUFA JOURNAL OF ENGINEERING مجلة الكوفة الهندسية}, volume={7}, number={3}, pages={13-26}, year={2016}, abstract={In this paper, an experimental study has been presented to investigate the effects of web opening on the behavior and failure of steel columns with cold formed thin walled sections (CFS) subjected to axial compressive load. Twenty small scale steel columns with cold formed box and channel sections and a total length of 500 mm have been considered in the experimental tests. Ten of the tested steel columns specimens have a box section with dimensions of (100×100×2) mm (height × width× thickness), and the other ten columns specimens have a channel sections with dimensions of (100×50×2) mm (height × width× thickness). To investigate the effect of the number and the shape of web opening on the axial compressive strength of steel columns, each ten columns with same cross section shape was divided into three groups of three columns in addition to the reference column which has no web openings. All groups of columns have same opening area which is located at the web of the section, but each group has a different opening shape (square, rectangular, and circular shapes), and each steel column within each group has different numbers of opening distributed along column length (one, two, and three openings). Each steel column specimens was subjected to an increasing static load up to column failure which indicated by the reloading of the test machine. The study has shown that for most of the tested columns, increasing the numbers of web openings results in decreasing the column axial strength compared to the reference steel column. The maximum percentage of the reduction in the columns axial compressive strength caused by the presence of web opening was found to be about 30% and 45% of the reference columns strength for columns with box and channel shape sections, respectively. It has also been found that the reduction in the axial compressive strength of the column specimens caused by the presence of web openings is lower for the circular shape openings compared to that for rectangular and/or square shape web openings.

يقدم هذا البحث دراسة عملية لتاثير الفتحات في منطقة الوترة على تصرف و فشل الاعمدة الفولاذية المكونة من مقاطع نحيفة الجدران. و المعرضة الى قوة انضغاط محورية . تم اخذ عشرين نموذج مصغر لاعمدة فولاذية بطول كلي يبلغ 500 ملمتر و بمقاطع بشكل صندوفي و مقاطع بشكل قناة مشكلة على الطريقة الباردة .عشرة من نماذج الاعمدة الفولاذية تتالف من مقاطع بشكل صندوقي وذات ابعاد 100×100×2 ملمتر (طول ×عرض×سمك) و العشرة الاخرى من نماذج الاعمدة تتالف من مقاطع بشكل قناة و بابعاد 100×50×2 ملمتر (طول ×عرض×سمك). لمعرفة تاثير شكل و عدد فتحات الوترة على تصرف و تحمل الاعمدة الفولاذية للقوة المحورية, تم تقسيم كل عشرة اعمدة بنفس شكل المقطع العرضي الى ثلاث مجاميع كل مجموعة تتالف من ثلاث اعمدة اضافة الى العمود المرجعي غير الحاوي على فتحات . كل مجموعة من الاعمدة الفولاية تحتوي على نفس مساحة الفتحة الواحدة الموجودة في منطقة الوترة ولكن كل مجموعة تحتوي على شكل معين للفتحات (مستطيل, مربع, و دائري) و كل عمود من الاعمدة الثلاثة ضمن كل مجموعة يحتوي على عدد مختلف من الفتحات ضمن منطقة الوترة (فتحة واحدة, فتحتان و ثلاثة فتحات). تم تسليط حمل محوري ستاتيكي متزايد منتظم على كل عمود لمعرفة اقصى حمل محوري ممكن تحملة من قبل كل عمود. تم الاستنتاج انه في اغلب الاعمدة الفولاذية التي تم فحصها في هذه الدراسة فان زيادة عدد الفتحات في منطقة الوترة تؤدي الى نقصان ملحوص في مقاومة العمود لقوة الانضغاط المحورية بالمقارنة مع مقاومة العمود المرجعي. لقد اظهرت النتائج ايضا ان النقصان في مقاومة العمود للقوة المحورية تكون اقل عند استخدام فتحات دائرية الشكل بالمقارنة مع النقصان الحاصل في مقاومة العمود للقوة عند استخدام فتحات مسنطيلة او مربعة الشكل.} }