TY - JOUR ID - TI - PREPARATION AND CORROSION BEHAVIOR OF NITI SHAPE MEMORY ALLOY COATED WITH BIOCOMPATABLE LAYER تحضير ودراسة سلوك التاكل لسبيكه نيكل- تيتانيوم المتذكرة للشكل مطليه بطلاء ذو توافق حيوي AU - Abdul Raheem. K. Abid Ali Zainab Jalal Ridha عبد الرحم كاظم عبد علي زينب جلال رضا PY - 2016 VL - 16 IS - 4 SP - 404 EP - 417 JO - Iraqi journal of mechanical and material engineering المجلة العراقية للهندسة الميكانيكية وهندسة المواد SN - 20761819 AB - In this paper NiTi shape memory alloy has prepared from elemental Nickel and Titanium powders by powder metallurgy Technique, the is 620 MPa compacting pressure , 850 ˚C temperature and10-3 torr vacuum atmosphere. The Porosity and density before and after sintering have been calculated. X-ray diffraction analysis showed that Nickel and Titanium are completely transformed into NiTi and Ni3Ti phase. Poly Methyl Methane Acrylate and Poly Methyl Methane Acrylate / Hydroxy apatite coating are applied to the surface of the alloy. Optical microscopy technique is used to characterize the surface of each sample. The corrosion rate has been studied in vitro by using electrochemical technique by a potentiostate in Hank’s Solution, Artificial saliva and 0.9% NaCl solution at 37 ºC. Atomic Absorption Spectroscopy technique is used to detect the Ni ion release from the alloy in 0.9% NaCl solution. The corrosion test results shows that the corrosion rate after Poly Methyl Methane Acrylate / Hydroxyapatite coating decreased from 12.14 mpy for bare sample into 0.132 mpy in 0.9% NaCl solution , from 4.94 mpy into 0.39 mpy Artificial saliva and from 12.66 mpy into 0.217 mpy in Hank Solution. The Ni release test shows that the amount of releasing Ni ion decreased into undetectable amount after coating with Poly Methyl Methane Acrylate and Poly Methyl Methane Acrylate / Hydroxyapatite.

في هذا البحث تم تحضير سبيكة نيكل-تيتانيوم المتذكره للشكل بواسطة تقنية ميتالورجيا المساحيق باستخدا ضغط كبس مساوي 620 MPa ودرجهة حراره تلبيد850 ˚C وبجو مفرغ 10-3 torr .تم حساب المساميه والكثافه قبل وبعد عملية التلبيد.فحص حيود الاشعه السينية اظهر ان النيكل والتيتانيوم تولا بالكامل الى NiTi و Ni3Ti .تم طلاء سطح العينات بطبقة بولي مثيل ميثان اكريليت وطبقة بولي مثيل ميثان اكريليتهيدروكسي اباتايت ومن ثم دراسة سطح العينات بواسطة المجهر الضوئي.معدل التاكل تم حسابه بالطريقه الكهروكيمائيه باستخدام جهاز المجهاد الساكن في محلول هانك,محلول اللعاب الصناعي,ومحلول 0.9% كلوريد الصوديوم بدرجة 37 ºC.كميه ايون النيكل المتحرر تم حسابها بواسطة مطيافية الامتصاص الذري بعد الغمر بمحلول 0.9% كلوريد الصوديوم .نتائج التاكل بينت ان معدل التاكل قد انخفض بعد الطلاء ب بولي مثيل ميثان اكريليتهيدروكسي اباتايت من 12.14 mpy قبل الطلاء الى 0.132 mpy في محلول0.9% كلوريد الصوديوم,ومن 4.94 mpy الى 0.39 mpy في محلول اللعاب الصناعي ومن 12.66 mpy الى 0.217 mpy في محلول هانك. فحص تحرر ايون النيكل اظهر ان تحرر ايون النيكل تم تقليله الى قيم لا يتحسسها جهاز مطيافيه الامتصاص الذري بعد الطلاء ب بطبقة بولي مثيل ميثان اكريليت وطبقة بولي مثيل ميثان اكريليت هيدروكسي اباتايت. ER -