TY - JOUR ID - TI - Improvement of Dynamic Buckling Behavior of Intermediate Aluminized Stainless Steel Columns تحسين سلوك الانبعاج الديناميكي لأعمدة الصلب المقاوم للصدأ المؤلمنة لمتوسطة الطول AU - Hameed Shamkhi Al-Khazaali حميد شمخي جابر الخزعلي AU - Samir Ali Al-Rabii سمير علي الربيعي AU - Ahmed Naif Al-Khazraji احمد نايف الخزرجي PY - 2017 VL - 13 IS - 1 SP - 26 EP - 41 JO - Al-Khwarizmi Engineering Journal مجلة الخوارزمي الهندسية SN - 18181171 23120789 AB - This paper experimentally investigated the dynamic buckling behavior of AISI 303 stainless steel aluminized and as received intermediate columns. Twenty seven specimens without aluminizing (type 1) and 75 specimens with hot-dip aluminizing at different aluminizing conditions of dipping temperature and dipping time (type 2), were tested under dynamic compression loading (compression and torsion), dynamic bending loading (bending and torsion), and under dynamic combined loading (compression, bending, and torsion) by using a rotating buckling test machine. The experimental results werecompared with tangent modulus theory, reduced modulus theory, and Perry Robertson interaction formula. Reduced modulus was formulated to circular cross-section for the specimens of type (1).The experimental results obtained showed an advantageous influence of hot-dip aluminizing treatment on the dynamic buckling behavior of AISI 303 stainless steel intermediate columns. The improvements based on the average value of critical stress were19.4 % for intermediate columns type (2) compared with columns type (1) under dynamic compression loading, 8.7 % for intermediate columns type (2) compared with columns type (1) under dynamic bending loading, and 16.5 % for intermediate columns type (2) compared with columns type (1) under dynamic combined loading.

تم في هذا البحث التحقق العملي لسلوك الانبعاج الديناميكي للأعمدة متوسطة الطول المؤلمنة وغير المؤلمنة من الصلب المقاوم للصدأ AISI 303 . حيث فحصت هذه الاعمدة تحت تاثير حمل الانبعاج الديناميكي، 27 عينة غير مؤلمنة (type 1) و 75 عينة مؤلمنة بطريقة الغمر الساخن (type 2)، وبظروف غمر مختلفة من درجة حرارة الغمر وزمن الغمر، بأستخدام ماكنة فحص الانبعاج الدوار ولحالة حمل الانضغاط الديناميكي (حمل انضغاط زائد حمل التواء) والانحناء الديناميكي (حمل انحناء زائد حمل التواء) وكذلك الحمل المركب (حمل انضغاط زائد حمل انحناء وحمل التواء). تم مقارنة النتائج مع نظرية tangent modulus theory ونظرية reduced modulus theory وصيغة Perry Robertson interaction formula. لغرض التمكن من استخدام نظرية reduced modulus theory فقد تم اشتقاق الصيغة الخاصة بأيجاد reduced modulus للمقطع الدائري. أظهرت النتائج الفائدة العملية المتحققة من عملية الالمنة بالغمر الساخن على سلوك الانبعاج تحت تأثير الاحمال الديناميكية. تمثل هذا التأثير الايجابي بتحسين مقاومة الانبعاج الديناميكي للاعمدة متوسطة الطول المستخدمة في هذا البحث بنسب مئوية لمتوسط الاجهاد الحرج، وهذه النسب على وفق النحو الاتي: (19.4 %) للاعمدة متوسطة الطول (type 2) مقارنة بالاعمدة (type 1) وتحت تأثير التحميل الانضغاطي الديناميكي، و (8.7%) للاعمدة متوسطة الطول (type 2) مقارنة بالاعمدة (type 1) وتحت تأثير حمل الانحناء الديناميكي و(16.5 %) للاعمدة متوسطة الطول (type 2) مقارنة بالاعمدة (type 1) وتحت تأثير التحميل الديناميكي المركب. ER -