@Article{, title={Optimization the Parameters of Magnetic Abrasive Process Using Taguchi Method to Improve the Surface Roughness المدخلات الامثل لعملية الحك الممغنط باستخدام طريقة تاكوشي لتحسين جودة خشونة السطح}, author={Shakir M. Mousa شاكر محمود موسى}, journal={Al-Khwarizmi Engineering Journal مجلة الخوارزمي الهندسية}, volume={13}, number={2}, pages={11-19}, year={2017}, abstract={Magnetic abrasive finishing (MAF) process is one of non-traditional or advanced finishing methods which is suitable for different materials and produces high quality level of surface finish where it uses magnetic force as a machining pressure. A set of experimental tests was planned according to Taguchi orthogonal array (OA) L27 (36) with three levels and six input parameters. Experimental estimation and optimization of input parameters for MAF process for stainless steel type 316 plate work piece, six input parameters including amplitude of tooth pole, and number of cycle between teeth, current, cutting speed, working gap, and finishing time, were performed by design of experiment (DOE) and response surface methodology (RSM).These six input parameters in this research were optimized for all input parameters to improve the surface layer for work piece by using signal-to-noise ratio technique. The obtained results showed that all six input parameters have an influence on the change in surface roughness(∆Ra). In addition, the results showed that the surface roughness of the work piece decreased from 1.130 to 0.370µm that means high level of improvement in the change of surface roughness (0.760)µm.

تعتبر عملية الحك الممغنط واحده من الطرائق غير التقليدية أو المتقدمة في الإنهاء السطحي وهذه الطريقة مناسبة للمواد المختلفة وتنيج مستوى عالٍ من الإنهاء السطحي وتستخدم القوة المغناطيسية لتسليط الضغط أثناء عملية القطع. مجموعة التجارب خطط لها على وفق مصفوفة تاكوشي وكانت بثلاثة مستويات وستة مدخلات, التقدير التجريبي وتعظيم الإفادة من المدخلات) ارتفاع الأسنان، وعدد خطوات الأسنان، والتي تتشكل شكل القطب الكهرومغناطيسي والتيار وسرعة القطع وفجوة العمل و وقت التشغيل) تم تنفيذا البحث باستخدام تصميم التجارب ومنهجية استجابة السطح, يمكن الاستفادة من هذا البحث هو لتحديد القيم المثلى لجميع المدخلات الستة التي تعطي أفضل سطح لتحسين الطبقة السطحية لمشغولة الفولاذ المقاوم للصدأ نوع 316 بأستخدام تقنية نسبة الإشارة إلى الضوضاء . وتشير النتائج بأن جميع المدخلات لها تأثير في تغير الخشونة السطحية. فضلا عن ذلك ان المحصلة النهائية أوضحت الى أن التغير في الخشونة السطحية انخفضت من (1,130- 0.370) مايكروميتر مما يدل على تحسن عالٍ في التغير في الخشونة السطحية مقداره (.760و0) مايكروميتر .} }