@Article{, title={THE EFFECT OF SHOT PEENING ON BENDINGSTRENGTH FOR MIG WELD JOINT ALUMINUM ALLOYS 2024 T351 تأثير القصف بالكرات على مقاومة الانحناء لسبائك الالمنيوم 2024 T 531 الملحومه بطريقة MIG}, author={Muammar Ibrahim Ismail معمر ابراهيم اسماعيل}, journal={Journal of Techniques مجلة التقني}, volume={30}, number={1}, pages={E60-E78}, year={2017}, abstract={Theinfluence ofshot peening onbending strength using MIG welding joint aluminum alloys 2024-T351 was studied. The paper implements many series of experimental techniques to figure the bendingstrength of all specimens , by performance hardness, shot peen, remaining stress and bending examinations for un-joint and joinedsamples. (MIG) process has implemented onsheets of "8mm thickness" to getbutt joiningconnections with measurement of (200 *100* 8) mm with joining readying angle in formsingle and double V of 75⁰and flatjoinby "ER- 4043(Al-Si5)"as a "groutmetal"and "argon" as protected gas. The juncturesareexamined by"X-ray radiography"and exceptedtheimperfect joint, then Welding joint exposed to heat treatment to removed joiningresidual stress.Hardness was measured using Vickers test and the specimens microstructure were examined, finally bending testimplemented on the samples which fabricated into typicalexaminationsample dimensionagreeing to the ASTM (E 190-92) of welded and un welded joints, and then ejaculation by steel ball in diameter 1.25 mm for 10 min to show the influence of shot peening on weld bendingThe Results of bendingqualities for MIGweld connected showdecay when comparing it with theunwedded joints and chiefly along the HAZ .but unweddedsamples were fiascoes nigh the middle line of the sample shot peening contributed in improvement of bending process for all specimens. Ansysprogram was used to conduct stress analysis operations.

درس هذا البحث تاثير طريقة القذف بكرات فولاذية على مقاومة الحني لسبيكة من سبائك الالمنيوم عالية المتانة هي T3512024 تم لحامها بطريقة القوس الكهربائي المحمي بغاز خامل وقد اجريت سلسلة من التجارب التقنية لتقييم مقاومة الحني للسبيكة تضمنتكل من اختبارات الصلادة, القذف بالكرات , الاجهادات الضغطية و البنية المجهرية للعينات الملحومة وغير الملحومة .انجز اللحام باستخدام لحام القوس الكهربائي المحمي بغاز على قطعتين من السبيكةالتي تم ذكرها بهدف انتاج وصلات تناكبية بالابعاد8)*( 200*100ملم اذ تم كسر حافات القطع من جهة ومن جهتين بزاوية مقدارها75درجة على شكل حرف Vووصلات بدون زوايا تحضيرية بواسطة سلك لحام رمزه4043 ERوالاركون كغار حمايةبعد عملية اللحام تم التاكد من عدم احتواء الوصلة على العيوب حيث تم فحصها بواسطة جهاز X-ray radiographyثم اجريت معاملة حرارية لغرض التخلص من اجهادات اللحام المتبقيه.صنعت عينات اختبار الحني من وصلات اللحام والمعدن بدون اساس اعتمادا على الابعاد القياسية ASTM (E 190-92) وكذلك اجراء عمليات فحص البنيةالمجهريه ,تم تعريض العينات الى القذف بكرات فولاذية قطرها 1.25mm وصلادة RC 55Hوبزمن 10 دقائق لبيان تاثير عملية القذف بكرات فولاذية على مقاومة الحني. للعينات الملحومة وغير الملحومة ومن النتائج التي تم الحصول علبها وجد ان القذف بكرات فولاذية ساهم في تحسين مقاومة الحني للعينات الملحومة من خلال معالجة عيوب اللحام . وتم استخدام برنامج Ansys لاجراء عمليات تحليل الاجهادات} }