TY - JOUR ID - TI - The Influence of Fines Content on the Mechanical Properties of Aggregate Subbase Course Material for Highway Construction using Repeated Load CBR Test AU - Adil N. Abid AU - Abdulhakim O. Salih AU - Esraa A. Nawaf PY - 2017 VL - 20 IS - 3 SP - 615 EP - 624 JO - Al-Nahrain Journal for Engineering Sciences مجلة النهرين للعلوم الهندسية SN - 25219154 25219162 AB - The effect of fines content (material finer than 0.075 mm) on the mechanical properties of subbase course aggregate is studied in this paper. a laboratory tests were carried out using percentage of fines material 5%, 10% and 15% by weight adding to the original subbase aggregate class B according to Iraqi specification (SCRB) which the specification limit the range of fines between 5-15%. The repeated load CBR test was done to study the mechanical properties; accumulative permanent, elastic deformation and equivalent elastic modulus. The RL CBR test was useful technique to assess the influence of fines material and stress level on the equivalent elastic modulus, and on the evolution of deformation. The equivalent modulus increase when adding 5% of fines material in case of plastic fines, but in case of non-plastic the increase continues until adding 10% fines material. Adding fines material also led to change in accumulative permanent deformation, where adding 5% fines material increase the permanent deformation by 36%, 5% for material with plastic fines and 20% for material with non-plastic fines for unsoaked samples. In case of soaked samples permanent deformation increase by 28% and 25% at adding fines material for material with plastic fines where decrease by 1% at adding 5% fines to original granular material with non-plastic fines. The theoretical modeling show that the deformation increase by increasing number of loads repetitions.

يقدم هذا البحث دراسة لتأثير المحتوى الناعم (المواد الأنعم من 0.075 ملم) على الخصائص الميكانيكية لركام طبقة تحت الأساس . الفحوصات المختبرية نُفذت بأستخدام نسب من المواد الناعمة 5%, 10% و 15% من الوزن مضافة الى ركام تحت الأساس نوع B حسب المواصفة العراقية الذي فيه حدود المواصفة للمواد الناعمة بين ( 5- 15%). تم تنفيذ فحص نسبة التحمل الكاليفورني للأحمال المتكررة لدراسة الخصائص الميكانيكية; التشوه الدائم التراكمي, التشوه المرن ومعامل المرونة المكافيء. فحص نسبة التحمل الكاليفورني للأحمال المتكررة تقنية مفيدة لتقييم تأثير المواد الناعمة ومستوى الاجهاد على معامل المرونة المكافيء وتطور التشوه. معامل المرونة المكافيء يكون في اعلى قيمة عند اضافة 5% من المواد الناعمة في حالة المواد الناعمة اللدنة لكن في حالة المواد عديمة اللدونة الزيادة تستمر حتى عند اضافة 10%من المواد الناعمة. اضافة المواد الناعمة كذلك يؤدي الى تغيير في التشوه الدائم التراكمي حيث اضافة 5% من المواد الناعمة يزيد التشوه الدائم بنسبة 36% و 5% بالنسبة للمواد ذات محتوى ناعم لدن وبنسبة 20% للمواد الحاوية على مواد ناعمة عديمة اللدونة للنماذج غير المغمورة. في حالة النماذج المغمورة التشوه يزيد بنسبة 28% و25% عند اضافة المواد الناعمة اللدنة بينما تقل بنسبة 1% عند اضافة 5% مواد ناعمة الى المواد الاصلية عديمة اللدونة . النمذجة النظرية اظهرت ان التشوه يزداد بإزدياد عدد مرات الحمل. ER -