TY - JOUR ID - TI - A Modified Reverse Engineering Approach Using Bezier Curve Approximation AU - Mustafa Saad Ayoob Al-Khazraji PY - 2017 VL - 20 IS - 5 SP - 1097 EP - 1104 JO - Al-Nahrain Journal for Engineering Sciences مجلة النهرين للعلوم الهندسية SN - 25219154 25219162 AB - Reverse Engineering is a process of re-producing existing parts by obtaining digital models using a special data taken from the original parts using specific techniques. It can be used to redesign existing parts either due to lost data or the parts are no longer available. In this paper, surface modelling technique using special data taken from CMM (Coordinate Measuring Machine) was employed to redesign a candle holder. Specific MATLAB code was generated to model the data taken from the surface of a candle holder made of glass. Bezier curve technique was implemented in this research to model the curve of the outer surface of the candle holder. Various orders of Bezier curves were discussed and used to give better approximation of the original data curve with error percentage monitoring each time. The thickness of the candle holder was reduced from 5mm to 3mm and the volume reduction was calculated. The amount of reduction in the glass volume when reducing the thickness was found to be 210mm3. In addition, the amount of increase in the area of glass section was calculated to be 138.5mm2. This reduction gives a better vision of the amount of glass saved using this procedure. Two different shapes were found and plotted by varying the control points coordinates.

الهندسة العكسية هي عملية اعادة تصنيع اجزاء مصنعة مسبقا عن طريق بناء نموذج الكتروني للجزء الاصلي وفقا لحسابات معينة. هذه الحسابات تؤخذ من النموذج الاصلي باستخدام تقنيات معينة و ثم معالجتها لغرض الحصول على شكل مقارب جدا للشكل الاصلي. تستخدم طريقة الهندسة العكسية لعمل نماذج مقاربة جدا للشكل الاصلي وذلك بسبب ضياع المخططات الاصلية التي تم تصنيع الجزء على اساسها او ان الشركة المصنعة لهذا الجزء قد اوقفت تصنيعه. في هذا البحث سوف يتم استخدام تقنية نمذجة السطوح لغرض اعادة تصنيع حامل شمع مصنوع من الزجاج باستخدام معلومات ماخوذة من ماكنة خاصة تسمى (CMM) تعطي احداثيات للسطح الخارجي لحامل الشمع. استخدم في هذا البحث برنامج ماتلاب لبناء كود خاص لمعالجة احداثيات السطح الخارجي للحامل. تم اعتماد طريقة منحني (بزير) عدة مرات (بتغيير درجة المنحني) لغرض ايجاد شكل تقريبي للسطح الخارجي للحامل مع حساب نسبة الخطا في كل مرة. تم تغيير سمك الجدار للحامل من 5سم الى 3سم و تم حساب كمية الزجاج المخفض لتكون 210ملم3 كذلك تم احتساب كمية الزيادة في المساحة السطحية للحامل لتكون 138.5ملم2. هذه النتائج تعطي تصور واضح عن فائدة الهندسة العكسية في تقليل كمية الزجاج المستخدم في صناعة حامل الشمع. كما و تم ايجاد اشكال مختلفة اضافية للحامل بتغيير مواقع النقاط في منحني بزير. ER -