TY - JOUR ID - TI - Optimization of Nano Hydroxyapatite/chitosan Electrophoretic Deposition on 316L Stainless Steel Using Taguchi Design of Experiments AU - Mohammed Jasim Kadhim AU - Nawal Ezzat Abdullatef AU - Makarim Hazim Abdulkareem PY - 2017 VL - 20 IS - 5 SP - 1215 EP - 1227 JO - Al-Nahrain Journal for Engineering Sciences مجلة النهرين للعلوم الهندسية SN - 25219154 25219162 AB - The aim of this work is to determine the optimum parameters for deposition of chitosan and mixture of chitosan and hydroxyapatite (HA) layers using electrophoretic deposition. The layers were on 316L stainless steel substrate. Taguchi approach was utilized to select the optimum parameters for both layers. The parameters used for deposition chitosan are voltage, time and temperature while the parameters used for HA and chitosan are voltage, time, concentration and temperature. Zeta potential tests were employed to measure the solutions stability. Coating layers were characterized for thickness, porosity and nanoroughness using optical microscopy (OM) and atomic force microscopy (AFM). The results from Taguchi design of experiments demonstrated that the best conditions for deposition of chitosan and HA layers are 50 V, 5 min, 3 g HA/L and 30C. The corresponding thickness, % porosity, nanoroughness and microroughness for optimum conditions were 22 µm, 3.53, 4.48 nm and 3.85 µm respectively.

يهدف البحث الى ايجاد الظروف المثلى لترسيب طبقة طلاء الكايتوزون والهيدروكسي ابتايت على السبيكة الاساس الفولاذ المقاوم للصدا بطريقة الترسيب الكهربائي الكاثودي . حيث تم ترسيب طبقة رقيقة من الكايتوزون فضلا عن استخدامه كمادة رابطة بين دقائق طبقات الهيدروكسيباتايت. استخدم الايثانول مع نسبة 5% ماء مقطركمحلول لعملية الترسيب مع 1% من حامض الخليك لاذابة الكايتوزون. تم استخدام برنامج تاكوجي لغرض اختيار الظروف المثلى لترسب طبقة الكايتوزن وتضمنت المتغيرات: فولتية، زمن الترسيب ، ودرجة حرارة كما استخدمت نفس المتغيرات لترسيب الهيدروكسي ابتايت مع اضافة متغير اخر وهو تركيز المسحوق. تم استخدام المجهر الضوئي (optical microscopy) ومجهرالقوى الذرية (AFM) لدراسة خصائص طبقات الطلاء من سمك ومسامية وخشونة. وقد اظهرت النتائج ان افضل الظروف لترسيب الكايتووزن هي(90 فولت، 11 دقيقة و40 مº ) وكان سمك الطبقة هو8 مايكرون واقضل الظروف للهيدروكسيابتايت هي (50 فولت ، 5 دقيقة ، 3 % هيدروكسيابتايت و30 مº) وكان سمك الطبقة هو 22 مايكرون والمسامية هي 3.53% والخشونة النانوية هي 4.48 نانومتر والخشونة المايكروية هي 3.85. ER -