TY - JOUR ID - TI - DEVELOPMENT OF FUZZY LOGIC MODEL FOR CUTTING PARAMETERS INFLUENCE ON THE CUTTING FORCE AND THE CHIP THICKNESS RATIO DURING TURNING OF ALUMINUM ALLOY 1350-O تطوير نموذج المنطق الضبابي لنمذجة تأثير متغيرات القطع على قوة القطع ونسبة سمك النحاتة أثناء خراطة سبيكة الألومنيوم 1350-O AU - Mohanned Mohammed H. AL-Khafaji مهند محمد الخفاجي PY - 2018 VL - 18 IS - 1 SP - 110 EP - 124 JO - Iraqi journal of mechanical and material engineering المجلة العراقية للهندسة الميكانيكية وهندسة المواد SN - 20761819 AB - In turning operation, numerous parameters are utilized to analyze machinability. Parameters, for instant, tool wear, tool life, cutting temperature, machining force components, power consumption, surface roughness, and chip thickness ratio are frequently utilized. The goal of this work is to model the effect of cutting parameters (cutting speed, depth of cut and feed rate) on the machining force and chip thickness ratio during turning ductile aluminum 1350-O. Four fuzzy logic models were built to model the relationship between cutting parameters and the three force components of machining force and the chip thickness ration. The inputs to all fuzzy logic models are cutting speed, depth of cut and feed rate. Whereas, the output for first, second, third and fourth models are cutting force, passive force, feed force and chip thickness ratio, respectively. All fuzzy models showed good match to the experimental data and the computed correlation coefficients were larger than or equal 0.9998. Those models were used to optimize the cutting process and give the optimum cutting parameters.

لتحليل قابلية التشغيل في عملية الخراطة يتم دراسة متغيرات متعددة مثل تآكل عدة القطع وعمر أداة القطع ودرجة حرارة القطع ومركبات قوى القطع واستهلاك الطاقة وخشونة السطح ونسبة سمك النحاتة. الهدف من البحث هو بناء نموذج لدراسة تأثير متغيرات القطع (سرعة القطع وعمق القطع ومعدل التغذية) على قوة التشغيل ونسبة سمك النحاتة. تم بناء أربعة نماذج المنطق الضبابي، ثلاثة نماذج استخدمت لتمثيل العلاقة بين متغيرات القطع ومركبات قوة التشغيل والرابع استخدم لتمثيل العلاقة بين متغيرات القطع ونسبة سمك النحاتة. ان المدخلات لجميع نماذج المنطق الضبابي هي سرعة القطع وعمق القطع ومعدل التغذية. بينما المخرجات لنموذج الأول والثاني والثالث والرابع هي قوة القطع وقوة الغير فعالة وقوة التغذية ونسبة سمك النحاتة، على التوالي. جميع النماذج التي تم بنائها أظهرت تطابق جيد مع النتائج العملية وكان معامل الارتباط لها اكبر من (0.9998). استخدمت هذه النماذج التي تم بنائها للحصول على أفضل قيم لمتغيرات القطع . ER -