@Article{, title={WIRELESS CONTROL SYSTEM TECHNIQUE FOR EVALUATING THE BUCKLING BEHAVIOR OF 6061-T4 AL-ALLOY تقنية نظام التحكم اللاسلكي لتقييم سلوك الانبعاج الجانبي لسبيكة الألمنيوم 6061-T4}, author={Husain .J. Mohamed Al-alkawi Abduljabbar owaid Hanfesh Hussein Fadhil Ajaj حسين جاسم محمد العلكاوي عبد الجبار عويد حنفيش حسين فاضل عجاج}, journal={Iraqi journal of mechanical and material engineering المجلة العراقية للهندسة الميكانيكية وهندسة المواد}, volume={18}, number={3}, pages={405-421}, year={2018}, abstract={This research deals with the evaluation of buckling behavior for 6061-T4 aluminum alloy under increasing compressive dynamic loads. Two types of columns, long, and the intermediate columns were used. The number of specimens used in the dynamic axial compression test were 9 samples. (1%) of the length column is the allowable lateral deflection. For the purpose of calculating the initial deflection, the digital dial gauge was used and the instrument was set at a distance of (0.7) of length from the fixed condition for the column. A control system is designed to evaluate the critical buckling and to prevent sample failure. The control system consists of a measuring circuit (transmitter circuit) with a flex sensor installed at 0.7 of the total column length of the column's fixed condition. In addition, the system contains a shutdown circuit (receiver circuit) to switch off the machine at critical load with a mobile phone for the purpose of displaying deflection data. The connection between the transmitter circuit and the receiver wirelessly through the RF sensor and between the transmitter circuit and mobile phone also wirelessly via Bluetooth. The results obtained were experimentally compared with the Perry-Robertson formula. It was found that the Perry-Robertson formula was a good agreement with the experimental results with a safety factor of (1.2) .

يتناول هذا البحث تقييم سلوك الانبعاج الجانبي لسبيكة الالمنيوم ((6061-T4 تحت زيادة حمل الضغط الديناميكي. تم استخدام نوعين من الأعمدة، طويلة، واعمدة متوسطة. كان عدد العينات المستخدمة في اختبار الضغط المحوري الديناميكي 9 عينات. ( 1٪ ) من طول العمود هو الانحراف الجانبي المسموح به. ولغرض حساب الانحراف الأولي، استخدم جهاز digital) dial gauge ) وتم تثبيت المقياس على بعد (0.7) من طول العمود من جهة التثبيت . تم تصميم نظام التحكم لتقييم الانبعاج الجانبي الحرج ومنع فشل العينة. يتكون نظام السيطرة من دائرة قياس (دائرة ارسال) مع flex) (sensor مثبت على بعد 0.7 من الطول الكلي للعمود من الحالة الثابتة للعمود ، اضافة الى ذلك يحتوي النظام على دائر اطفاء (دائرة استقبال) مع هاتف نقال لغرض عرض بيانات الانحراف . الاتصال بين دائر المرسل والمستقبل لاسلكيا عن طريق RF sensor)) وبين دائرة المرسل والموبايل ايضا لاسلكيا عن طريق البلوتوث. تمت مقارنة النتائج التي تم الحصول عليها تجريبيا مع صيغة بيري روبرتسون. وقد وجد أن صيغة بيري-روبرتسون تتوافق بشكل جيد مع النتائج التجريبية مع عامل أمان قدره (1.2).} }