@Article{, title={Preparing Composite Materials from Commercially Pure Aluminum Scrap and Reinforced Iron Oxides Fe3O4 & Fe2O3 تحضير مواد متراكبة من خردة الألمنيوم ذو النقاوة التجارية وتدعيمها بدقائق أكاسيد الحديد Fe3O4 & Fe2O3}, author={Mohammed Abdulateef Ahmed محمد عبد اللطيف أحمد}, journal={DIYALA JOURNAL OF ENGINEERING SCIENCES مجلة ديالى للعلوم الهندسية}, volume={10}, number={4}, pages={59-71}, year={2017}, abstract={This study is concerned with investment of the commercial purity aluminum scrap (1100) by converting it to aluminum matrix composite reinforced by iron oxides particles. The particle size, X-RD and microstructure of the oxides particles were found. The weight ratio of added oxides was (1%, 1.5% & 2%) .Wettabilty was improved by pure magnesium additive. Electric mixer is used to dispersing iron oxides particles in the aluminum scrap molten. After that, was cut the composite to samples and prepared these to tests such as; tensile strength, compression strength, hardness, wear resistance, impact strength (toughness), corrosion resistance and microstructure. From tests above found that; tensile strength, compression strength, wear resistance, hardness were increased in composite compared to the base metal , while impact strength (toughness)and corrosion resistance were lowered slightly in composite compared to the base metal .In wear resistance test used (pin-on-disk) technique where load ,sliding velocity and sliding distance were constant. The microstructures were taken for base metal and composite before and after corrosion to comparison.

يتلخص هذا البحث بأستثمار خردة الألمنيوم ذو النقاوة التجارية (1100) بتحويله لمادة متراكبة ذات أساس المنيوم مدعمة بدقائق أكاسيد الحديد بعد أيجاد الحجم الحبيبي وحيود الأشعة السينية X-RD والصورة المجهرية لدقائق الأكاسيد ، والنسبة الوزنيةلأضافة الأكاسيد(1%,1.5% & 2%) ، وتم تحسين قابلية الترطيب بأستخدام معدن المغنسيوم النقي. وبأستخدام مازج كهربــــائي لتحضير المادة المتراكبة المتكونة من تشتيت دقائق أوكسيد الحديد لتدعيم منصهر خردة الألمنيوم أو (أرضية المادة المتراكبة).وبعدها تقطع المادة المتراكبة وتشغل الى عينات بما يتلائم وفحوصات مقاومة الشد والأنضغاط والصلادة والبلى والصدمة و مقاومة التآكل و الفحص المجهري . ولوحظ بعد أجراء الفحوصات أعلاه بأن مقاومة الشد ومقاومة الأنضغاط ومقاومة البلى والصلادة قد أزدادت بالمادة المتراكبة أكثر من السبيكة الأساس . وفي أختبار مقاومة البلى تم أستخدام البلى الجاف الأنزلاقي (Pin-on-Disk) حيث الحمل وسرعة الأنزلاق ومسافة الأنزلاق ثابتة ،أما الفحوصات المجهرية للعينات المدروسة فقد أخذت للسبيكة الأساس و للموادة المتراكبة قبل وبعد التآكل للمقارنة فيما بينها .} }