TY - JOUR ID - TI - Optimizationof EDM Process Factors for MachiningAl-Si Alloy Using Response Surface Methodology AU - Saad H. Al-Shafaie AU - Nada Talib PY - 2018 VL - 26 IS - 10 SP - 217 EP - 228 JO - Journal of University of Babylon مجلة جامعة بابل SN - 19920652 23128135 AB - This work exhibits an incorporated way to deal with the procedure demonstrating and multi-target improvement of EDM parameters of Al-Si based on response surface methodology (RSM) combined with desirability function (DF) method. The’ effect’ of’ process’parametersfor’ example, pulse current (Ip), pulse’ on’ time’ (Ton) as well as pulse’off’ time’ (Toff) on’metal removal’ rate’ (MRR), electrode’ wear’ rate’ (EWR) and’ surface’ roughness’ (Ra), were analyzed. An extensive investigation of difference (ANOVA) at fixed indicative level of 5%,was done to completely distinguish the most persuasive parameters, and the sufficiency of all fitted relapse models were checked. To completely comprehend the trademark machinability conduct under various EDM conditions, fundamental effect investigation. The results indicate that MRR increases with the rising Ip and Ton. Low EWR and Ra can be acquired by diminishing Ip and Ton. Be that as it may, the Ip is the most commanding parameter pursued by Ton and Toff for MRR and Ra whereas in the EWR, the Ip is the foremost factor, followed by the Toff and Ton.Lastly, a multi-optimization waydependent upon the desirability function (DF) idea was used to discover ideal blends of machining parameters so that it was capable to produce the the most extreme estimation of MRR and least estimations of EWR and Ra, inside the noteworthy information parameters.

يقدم هذا البحث نهجا متكاملا لنمذجة العملية والأمثلية متعددة الاهداف لمتغيرات التشغيل بالشرارة الكهربائية لسبيكة الالمنيوم سيليكون (Al-Si) اعتمادا على نمط استجابة السطح (RSM) إلى جانب تكنيك دالة الرغبة (DF).أختيرت ثلاث متغيرات منفصلة كمدخلات وهي تيار النبضة (Ip)، فترةإفراغ النبضة (Ton) وفترة توقف النبضة (Toff) للتأكد من تأثير المتغيرات الثلاث سابقة الذكر على المخرجات المتمثلة بمعدل إزالة المادة (MRR)، معدل بلى القطب (EWR) وخشونة السطح (Ra). تحليل عامللتفاوت (ANOVA) عند درجة من الأهمية مقدارها 5%لتعيين المعاملات الأكثر تأثيرا، وأنجزاختبار مدى كفاءة كافة النماذج. ولفهم السلوك الشامل لقابلية تشغيل لسبيكة الالمنيوم سيليكون (Al-Si) تحت أوضاع التشغيل المتفاوتة، تمإجراء تحليل التأثيرالأساسي. بينت النتائج ان معدل الازالة المعدنية يزداد مع رفع تيار النبضة وفترةإفراغ النبضة. يمكن الاستحصال ايضا على نقصان في كل من معدل بلى القطب وخشونة السطح عن طريق خفض تيار النبضة ووقتإفراغ النبضة. ومع ذلك، فإن تيار النبضة هو العامل المتحكم (الاكثر تأثيرا) على معدل الازالة المعدنية وخشونة السطح متبوعا زمن تفريغ النبضة وزمن توقف النبضة، في حين أن في معدل بلى القطب فان تيار النبضة هو العامل الاكثر تأثيرا يليه زمن توقف النبضة وزمن إفراغ النبضة. أخيرا استعملتأسلوبالامثلية متعددة الاهداف بالاعتماد على نظرية دالة الرغبة للاستحصال على المقدار الامثل لمتغيرات التشغيل بحيث يمكن الاستحصال من خلالها على اعلىمقدار لمعدل الازالة المعدنية وأدنى مقدار لكل من متوسط بلى القطب وخشونة السطح مع المتغيرات المؤثرة. ER -