TY - JOUR ID - TI - Flexural Performance of Laced Reinforced Concrete Beams under Static and Fatigue Loads تصرف الانحناء للعتبات الخرسانية ذات التسليح المربط تحت تاثيرالاحمال الساكنة والاعياء AU - Abbas AbdulMajeed Allawi عباس عبد المجيد علاوي AU - Hayfaa D. H. Al-Abboodi هيفاء ضمد حسن العبودي PY - 2019 VL - 25 IS - 10 SP - 134 EP - 153 JO - Journal of Engineering مجلة الهندسة SN - 17264073 25203339 AB - This paper introduces experimental results of eighteen simply supported reinforced concrete beams of cross sections (160 mm×300 mm) and length 3000 mm to study the effect of lacing reinforcement on the performance of such beams under static and fatigue loads. Twelve reinforced concrete beams (two of them are casted with vertical shear reinforcement used as control beams) are tested under four points bending loading with displacement control technique and six laced reinforced concrete beams were exposed to high frequency (10 Hz) by fixing the fatigue load in each cycle. Three parameters are used in the designed beams, which are: lacing bar diameter (4mm, 6mm, and 8mm), lacing bar inclination angle to horizontal〖 (30〗^°,〖45〗^° and 〖60〗^°), and lacing steel ratio depending on number of lacing bar in each longitudinal face of beam and lacing bar diameter. The comparison results of experimental tests revealed that the ultimate loads of laced reinforced concrete beams are higher than the conventional reinforced concrete beams due to increasing lacing bar diameter, angle of inclination lacing bar, and lacing steel ratio, while the deflection is reduced. Also, the laced reinforced concrete beams can safely withstand the fatigue loading.

يقدم هذا البحث النتائج العملية لثمانية عشر عتبة خرسانية ذات الاسناد البسيط وبمقطع (160ملم ×300 ملم) وطول 3000 ملم لدراسة تأثير التسليح المربط على أداء هذه العتبات تحت تاثيرالأحمال الساكنة والكلل. تم اختبار اثنتي عشرة عتبا خرسانيا مسلحا (اثنان منها ذات تسليح قص العمودي واستخدمتا كعتبات مرجعية) تحت أربع نقاط تحميل باستخدام تقنية التحكم في الإزاحة ، كما تعرضت ست عتبات خرسانية مسلحة لحمل كلل ذو تردد عالي (10 هرتز) عن طريق تثبيت حمل الكلل في كل دورة.استخدمت ثلاث محددات في تصميم العتبات ، وهي: قطرالحديد المتعرج (4 مم ، 6 مم ، و 8 مم) ، وزاوية ميل االحديد المتعرج إلى الافق (30°,45°و 60°)، ونسبة الحديد المتعرج التي تعتمد على عدد الحديد المتعرج في كل وجه طولي (واحد أو اثنين) وقطر الحديد المتعرج. أوضحت نتائج المقارنة للفحوصات العملية أن الأحمال القصوى للعتبات الخرسانية المسلحة أعلى من العتبات الخرسانية المسلحة التقليدية بسبب زيادة قطر الحديد المتعرج ، وزاوية الحديد المتعرج ، ونسبة الحديد المتعرج ، في حين الهطول قل. كما ان العتبات الخرسانية ذات التسليح المربط تستطيع مقاومة حمل الكلل بأمان. ER -