TY - JOUR ID - TI - الخصائص الفيزيائية لنظام(بازلت-نيكل) بتقنية الرش الحراري باللهب AU - باسل صباح احمد* AU - اسماعيل خليل جاسم PY - 2019 VL - 27 IS - 4 SP - 98 EP - 108 JO - Journal of University of Babylon مجلة جامعة بابل SN - 19920652 23128135 AB - Many surfaces suffer cracks and external corasion such as turbo blades and oil pipes. In order to solve these problems are used coatings of high durability and low cost. In the current research, the powder of the basalt with multiple oxides supported by metal (Ni) 50% was sprayed models with thermal spraying by flame and at multiple spraying distances of (10,12,14,16,18,20) cm after the preparation of the models coated on a base of alloy steel, the process of sintering of the samples at (700, 900, 1100)℃ and within two hours have been done. The mechanical tests were (strength adhesion, porosity, hardness, wear and tear) (SEM) for prepared samples before and after sintering. The results showed that the best spraying distance was 16 cm and the best heat treatment is ( (1100 ℃), depending on the results of the adhesion strength tests at (24.43 MPa) and (8.653%) porosity, (1140 Hv) and the hardness of the Vickers and at a constant sliding speed (12000 cm / min). The results of the scanning electron microscopy showed clear surface consistency after thermal conductivity with a few pores and treatments the best (1100.).

تعاني العديد من السطوح تشققات وتأكل خارجي مثل الريش التوربينية وانابيب النفط ولأجل حل تلك المشاكل يتم استخدام طلاءات ذات متانة عالية وكلفة واطئة. ففي البحث الحالي تم استخدام مسحوق صخور البازلت((Basalt ذات الاكاسيد المتعددة مدعمة بمادة معدنية (Ni)50% تم رش النماذج المجهزة بتقنية الرش الحراري بواسطة اللهب وعند مسافات رش متعددة هيcm (10,12,14,16,18,20) وبعد اكمال تحضير النماذج المطلية على قاعدة من الفولاذ السبائكي تم اجراء عملية التلبيد للعينات وعند معاملة ((700℃, 900℃,1100℃ وبزمن ساعتين. اما الفحوص الميكانيكية تمثلت ب( قوة التلاصق, المسامية, الصلادة, البلى) وكما تم اجراء فحص بالمجهر الالكتروني الماسح(SEM) للعينات المحضرة قبل وبعد عملية التلبيد. اظهرت نتائج الفحص ان احسن مسافة رش كانت cm 16 وافضل معاملة حرارية هي ( (1100℃ وذلك بالاعتماد على كل من نتائج فحوص قوة التلاصق التي بلغتMPa(24.43) و المسامية التي بلغت %((8.653 وصلادة فيكرز هي (HV 1140) وكما ووجد عند سرعة انزلاقية ثابتة هي (cm/min.12000) وعند زمن خمسة دقائق وحمل ( (20Nالحصول على اوطئ معدل بلى(wear)هو (0.397), اما نتائج فحص المجهر الالكتروني الماسح اوضحت تناسق سطحي واضح بعد اجراء المعاملات الحرارية مع وجود قليل للمسامات ER -