TY - JOUR ID - TI - Removal of Reactive Dyes by Electro Coagulation Process from Aqueous Solution ازاله الاصباغ الفعالة من المحاليل المائية بواسطة عملية التخثير الكهربائي AU - Zahraa A. Sadoon زهراء عادل سعدون AU - Mohanad J. M-Ridha مهند جاسم محمد رضا PY - 2020 VL - 26 IS - 2 SP - 14 EP - 28 JO - Journal of Engineering مجلة الهندسة SN - 17264073 25203339 AB - The presence of dyes in wastewater has become a major issue all over the world. The discharge of dyes in the environment is concerned for both toxicological and esthetical reasons. In this study, the removal of dyes from aqueous solution by electrocoagulation using aluminum electrodes as cathode and anode were investigated with the electrocoagulation cell of 1litter. The study included: the impact of various operating parameters on the dyes removal efficiency like pH, NaCl concentration, distance between electrodes, voltage, initial dyes concentration and type of electrodes. The dye (congo red) concentrations were (50, 100, 150, and 200 ppm), stirring speed was 120 rpm at room temperature. pH used was maintained constant. The impact of voltage values was chosen as 6, 10, and 14 Volts. On increasing voltage dyes, removals increased significantly. The higher removal efficiency of dyes (99.9%) was achieved at (30) minutes for (Al/Al) electrodes at pH 6.5-7 and voltage 14 Volts. The results showed that the best amount of sodium chloride was found to be 600 ppm in dyes, voltage of 14 Volts, and best gap between the electrodes as 0.5 cm.

في هذا البحث استخدمت طريقة التخثير الكهربائي لمعالجة الماء الملوث الاصباغ وباستخدام أقطاب أنود من الألمنيوم كمخثر وأقطاب كاثود من الألمنيوم ايضا. خلية تخثير بحجم 1 لتر قد استخدمت أيضا في العمل تم دراسة العديد من العوامل المؤثرة على عملية معالجة المياه الملوثة بالأصباغ وكانت هذه العوامل كالتالي: الدالة الحامضية, الجهد, التركيز الأولي للأصباغ , تركيز كلوريد الصوديوم, المسافة بين الأقطاب تم دراسة هذه المتغيرات بدرجة حرارة الغرفة وسرعة التحريك (120) دورة بالدقيقة وتركيز الاصباغ الأولي كان (50,100,150,200جزء بالمليون ) وقد تم اخذ قيم فرق الجهد هي (6,10,14 فولت) وفي تحديد الرقم الهيدروجيني الأفضل تم تثبيته في دراسة المتغيرات الاخرى وجد عند زيادة فرق الجهد تزداد عملية أزالة الاصباغ ومن النتائج تبين ان الازالة المثلى كانت 99.9% و قد تحققت بزمن 30 دقيقة بدالة حامضية تساوي 7 وفرق جهد 14 فولت وباستخدام أقطاب ألمنيوم . وبتركيز كلوريد صوديوم يساوي 600 جزء بالمليون ومسافة 0.5 سنتيميتر ER -