TY - JOUR ID - TI - Influence of the Yttria and Graphite Particles on the same of Al 2024 Alloy Properties تأثير جسيمات اليتيريا والكرافيت على بعض خواص سبيكة األلمنيوم 2024 AU - Raed N. Razooqi AU - Ahmed A. Akbar AU - Mohanad L. Hamada PY - 2019 VL - 26 IS - 4 SP - 1 EP - 7 JO - Tikrit Journal of Engineering Sciences مجلة تكريت للعلوم الهندسية SN - 1813162X 23127589 AB - Powders have been mixed as (Al with 99% purity ≤53µm particle size, Cu with 99.5% purity ≤53µm particle size, Mg with 99.5% purity ≤53µm particle size, Y2O3 with 99.9% purity ≤53µm particle size, Gr with 99.9% purity ≤53µm particle size). one set of composite samples was prepared by addition (3wt%Gr) to metal powders shown above. For the each sample of composite varying (Y2O3) weight percentage as: (Al 2024-3wt%Gr-XY2O3) was added x=(0,2,4,6,8)(wt%) the other set of composite was in opposite. Well mixed samples was pressed uniaxial with (700 Mpa) and (30sec). the compacted samples were sintered at (6000C) for (2hr). Results have shown an increase in bulk density by (5.3%) for (Al 2024-3wt% Gr-XY2O3) with the increase of reinforcement until (8wt%) of (Y2O3), while bulk density have been reduced for (Al 2024-3wt%Y2O3-XGr) with (5%) with the increase of (Gr) weight content in the composite. An increase in real porosity was noticed with the increase of (Y2O3) with (8wt%) (11.9%) for (Al 2024-3wt%Gr-XY2O3) but this was less in comparison with (Al 2024-3wt%Y2O3-XGr) were porosity increase with the increase of (Grwt%) up to reduced (18.5%) at (8wt%Gr).Mean value was of micro hardness decreased gradually with the increase of (Grwt%) to reach (19.4%) reduction at (8wt%Gr) in opposite the micro hardness mean value increased by (20%) as (Y2O3wt%) increased to (8wt%).Compression strength have was increased by (51%) as (Y2O3) content increased from (2-8)(wt%) for (Al 2024-3wt%GrXY2O3)composite, while it was decreased by (48%) with the addition of (8wt%) graphite to (Al 2024-3wt%Y2O3-XGr).The content of (Gr) had higher effect on wear rate than (Y2O3) where the wear rate decreased by (59.7%) and (41%) for composite samples respectively, within the limits of addition in the current study.

تم خلط المساحيق الألومنيوم ذي نقاوة %99 وبحجم جسيمي µm≥53 ،النحاس ذي نقاوة %5.99 وحجم جسيمي µm≥53 ،المغنيسيوم ذي نقاوة %5.99 وحجم جسيمي µm≥53 مع جسيمات اليتيريا Y2O3 ذي نقاوة %9.99 وحجم جسيمي µm≥53 والكرافيت ذي نقاوة %9.99 وحجم جسيمي µm≥53 بمرحلتين الأولى إضافة مسحوق الكرافيت بنسبة ثابتة مقدارها %3wt إلى متراكبات xY2O3-Gr%3wt-Al2024 إذ أن %wt8,6,4,2,0=x أما المرحلة الثانية فتمثلت بإضافة مسحوق الكرافيت بنسب متغيرة x مع تثبيت نسبة اليتيريا لتكون بمقدار %3wt إنتاج متراكبات xGr-Y2O3%3wt-Al2024 ،كبس الخليط على الباردباتجاه واحد بضغط كبس مقداره 700 MPa ولمدة 30 sec .وأجريت عملية التلبيد عند درجة حرارة 600 oC لمدة ساعتين ، أظهرت نتائج الدراسة الحالية زيادة في الكثافة الحجمية بمقدار %3.5 للمتراكبات xY2O3-Gr%3wt-Al2024 مع زيادة النسب الوزنية لجسيمات اليتيريا حتى الوصول إلى %8wt ،بينما انخفضت الكثافة الحجمية للمتراكبات xGr-Y2O3%3wt-Al2024 بمقدار %5 عند زيادة محتوى جسيمات الكرافيت كما ازدادت المسامية الحقيقية مع زيادة محتوى اليتيريا بمقدار %9.11 للمتراكبات xY2O3-Gr%3wt-Al2024 لكنها الأقل بالمقارنة مع المتراكبات التي تحتوي على نسبة ثانية من اليتيريا إذ ازدادت نسبة مساميتها بزيادة محتوى الكرافيت وبلغت %5.18 عند محتوى كرافيت %8wt ،أما الصلادة المتوسطة فقد أنخفضت بشكل تدريجي مع زيادة محتوى الكرافيت لتصل إلى %4.19 عند الوصول إلى محتوى كرافيت %8wt ،ولكن عندما بلغ محتوى جسيمات التقوية باليتيريا نسبة %8wt ازدادت الصلادة المتوسطة للمتراكبات بنسبة %20 .وعند زيادة محتوى جسيمات التقوية للمتراكبات من %wt8-2 ازدادت مقاومة الانضغاط بنسبة %51 عند التقوية باليتيريا بينما انخفض بنسبة %48 عند التقوية بالكرافيت. وكان لمحتوى الكرافيت تأثير كبير على معدل البلى مقارنة مع اليتيريا إذ انخفض بالمقدارين %41 و%7.59 على التوالي ضمن حدود النسب المضافة قيد الدراسة. ER -