TY - JOUR ID - TI - Mechanical and Petrological Properties of Gercus Formation in Dukan Area, Kurdistan of Iraq الخصائص الميكانيكية والبترولوجية لتكوين جركس في منطقة دوكان بكوردستان العراق AU - Dr. Kamal Ahmad Rashed1 د. كمال أحمد رشيد AU - Dr. Hyam Saleh Daoud2 د. هيام صالح داود AU - Dr. Younis Mustafa Alshkane1 د.يونس مصطفى الشيخاني PY - 2018 VL - 5 IS - 1 SP - 27 EP - 39 JO - Sulaimania Journal for Engineering Sciences مجلة السليمانية للعلوم الهندسية SN - 24101699 24156655 AB - The mechanical properties of Gercus Formation in Iraq such as Uniaxial Compressive Strength (UCS), Tensile Strength (TS), Point Load Strength and Young’s Modulus (E) are very crucial to design structures in or on the Formation. Unfortunately, there is no information about these mechanical properties as well as about predicting these properties using non-destructive tests such as the ultrasonic pulse velocity (UPV). The aim of this study is to evaluate these mechanical properties for Gercus Formation and to develop the correlation equations to find the mechanical properties from simple indirect tests such as point load test (PLT) and non-destructive test (UPV). Fifty one core samples (75mm diameter and 150 mm height) were collected from Gercus formation at Surqawshan Dam Project in Iraq and prepared for physical and mechanical testing. The obtained results showed that the mechanical properties of the Gercus Formation can be obtained using non-destructive test (UPV) whereas the point load test is not a good choice to predict the mechanical properties of the formation. Furthermore, the petrological properties of Gercus Formation have been studied macroscopic and microscopic by thin sections. Based on the petrological analysis, the collected samples were classified in white dolomitic limestone, gray shale, red silty sandstone and red clayey sandstone.

ان الخصائص الميكانيكية لتكوين جركس في العراق مثل الضخط الأحادي المحور، ضخط الشد، ضخط الحمل النقطي و كذلك معامل يونغ مهمة جدا لتصميم الهياكل داخل أو على هذه التكوين. لسوء الحط لاتوجد معلومات حول الخصائص الأنفة الذكر وكذلك حول علاقات الترابط لايجاد هذه الخصائص باستخدام اختبارات غير مدمرة مثل سرعة النبض بالموجات فوق الصوتية. الهدف من هذه الدراسة هو تقييم الخواص الميكانيكية المذكورة لتكوين جركس وتطوير معادلات الأرتباط لايجاد الخواص الميكانيكية بالأعتماد على التجارب المختبرية البسيطة مثل تجربة ضخط النقطي والتجربة الغير المدمرة (سرعة النبض بالموجات فوق الصوتية). تم جمع وتحضير ودراسة احدى و خمسون نموذجا اسطوانيا (قطر 75 ملم و ارتفاع 150 ملم) من مشروع سد سورقاوشان شمال العراق. النتائج التي تم الوصول اليها تشير الى أنه يمكن الحصول على الخصائص الميكانيكية لتكوين جركس باستخدام سرعة النبض بالموجات فوق الصوتية بينما لا يمكن اعتماد على تجربة الضخط النقطي لحساب هذه الخصائص لانها لم تعطي نتائج جيدة. كذلك تمت دراسة الخصائص البترولوجية لهذا التكوين في الحقل و في المختبر اعتمادا على المقاطع الرقيقة. بناءا على التحليل البترولوجي تم تصنيف النماذج المدروسة الى: الصخر الكلسي الدولوميتي الأبيض، الطين الصفائحي رمادي اللون، الصخر الرملي السيلتي الأحمرو الصخر الرملي الطيني الأحمر. ER -