TY - JOUR ID - TI - Influence of Nd:YAG Laser Energy on Mechanical properties of Nitriding Steel تأثير طاقه الليزر النبضي Nd:YAG على الخصائص الميكانيكه للفولاذ المنترد AU - Abbas S. Alwan عباس علوان شياع AU - Enass A. Khalid ايناس عبد الكريم خالد AU - Ansam Abdul Jabbar Aziz انسام عبد الجبار عزيز PY - 2020 VL - 23 IS - 2 SP - 187 EP - 193 JO - Al-Nahrain Journal for Engineering Sciences مجلة النهرين للعلوم الهندسية SN - 25219154 25219162 AB - Desired mechanical properties like microstructure, micro hardness and wear resistance are the key parameters for which low carbon steel (AISI 1006) are widely selected. Surface heat treatment applied to improve these properties; traditionally surface heat treatments like induction hardening, in recent time’s laser surface hardening. In this work, thermochemical treatment (liquid nitriding) by using mixture from 61% NaCN, 15% K2CO3 and 24% KCL and followed by Nd:YAG laser surface treatment was done . The laser parameter were energy (0.89, 2, 4 and 9) J, spot diameter (0.790 ,0.33, 0.283 and 0.224) mm, pulses duration (1, 2.33, 4.47 and 9.87) ms with fix wavelength 1604nm. Laser surface treatment cycle was melting the layer surface, holding and rapid cooling in air medium. Optical microscopy (OM) and scanning electron microscope (SEM) has been used to study the microstructures and cross-sectional of molted and heat affected zones respectively. The wear test was done to measure the wear rate by using pin -on-disk principles were satisfied. The result shown that increasing in laser energy effects to increase in the area of melted and heat affected zones of nitriding steel. Also increasing in laser energy led to increase micro hardness about 61%, while wear rate decrease about 40 % and increased depth of molted zone.

الخصائص الميكانيه المرغوبه مثل البنيه المجهريه , الصلابه الدقيقه ومقاومه التأكل هي المعاملات الرتيسه التي يتم اختيار الفولاذ المنخفض الكاربون (AISI1006) لها على نطاق واسع . ولتحسين هذه الخصائص يم تطبيق المعالجه الحراريه السطحيه,المعاملات الحراريه التقليديه مثل التصلب بالحث وفي الاونه الاخيره تصلب السطح بالليزر.في هذا العمل تم اجراء المعالجه الحراريه الكيمائيه (النترده السائله)باستخدام خليط مكون من 61%سينانيد الصوديوم ,15% كاربونات البوتاسيوم و 24% من كلوريد البوتاسيوم ,متبوعا بالمعالجه السطحيه بالليزر النبضي Nd :YAG كانت متغيرات الليزر ,طاقه 0.89 ,2 ,4, و9 جول ,قطر النبضه 0.33 ,0.790,0.224 و 0.283 مليمتر ,مده النبضه 1 ,2.33,4.47 و 9.87 ملي ثانيه مع طول موجه ثابت 1064نانومتر .تم استخدام المجهر الضوئي(OM) والمجهر الالكتروني الماسح (SEM)لدراسه الهياكل المجهريه والمقاطع العرضيه للمناطق المتأثره بالحراره على التوالي .تم اجراء فحص التاكل لمعرفه معدل التأكل, .أظهرت النتائج ان زياده زياده طاقه الليزر ادت الى زياده في مساحه المنطقه المنصهره والمنطقه المتاثره بالحراره من الفولاذ المنترد ,كما أدت الزياده في طاقه الليزر الى زياده الصلابه الدقيقه بحوالي 61% بيمنما انخفض معدل التاكل بحوالي 40% وزياده عمق المنطقه المنصهره. ER -