@Article{, title={The effect of composite bonding spot size and location on the performance of poly-ether-ether-ketone (PEEK) retainer wires تأثير حجم وموقع الترابط المركب على أداء أسلاك التجنيب متعدد الأثير وإيثر كيتون (نظرة خاطفة)}, author={Akram Faisal Alhuwaizi أكرم فيصل الحويزي and Akram Faisal Alhuwaizi أكرم فيصل الحويزي and Ammar Salim Kadhum عمار سليم كاظم and Ammar Salim Kadhum عمار سليم كاظم}, journal={Journal of baghdad college of dentistry مجلة كلية طب الاسنان بغداد}, volume={33}, number={2}, pages={1-9}, year={2021}, abstract={Background: Poly-ether-ether-ketone(PEEK) has been introduced to many dental fields. Recently it was tested as a retainer wire‎ following orthodontic treatment. This study aimed to investigate the effect of changing the bonding spot size and location on the performance of PEEK retainer wires. Methods: A biomechanical study involving four three-dimensional finite element models was performed. The basic model was with a 0.8 mm cylindrical cross-section PEEK wire, bonded at the center of the lingual surface of the mandibular incisors with 4 mm in diameter composite spots. Two other models were designed with 3 mm and 5 mm composite sizes. The last model was created with the composite bonding spot of the canine away from the center of the crown, closer to the lateral incisor. The linear displacement of the teeth, strains of the periodontal ligament, and stresses in PEEK wire and composite were evaluated. The data was numerically produced with color coded display by the software. Selected values were tabulated and compared among models. Results: The amount of linear displacement and strain was very low. Stresses in the wire and composite were affected by the size and position of the composite bonding spot. The safe limits were identified at 235 MPa for PEEK and 100 MPa for composite. The basic model had a von Mises stress in the PEEK wire of 122.09 MPa, and a maximum principal stress in the composite of 99.779 MPa. Both stresses were within the safe limits, which means a lower risk of failure in PEEK and composite. All other models had stresses that exceeded the safe limit of the composite. The 3 mm composite model was the only one that developed stresses in the wire more than the safe limits of PEEK. Conclusions: Within the limitations of this study, bonding PEEK wires with 4 mm bonding spots to the clinical crown center provided the best mechanical performance of the wires and spots; otherwise, the mechanical properties of the wire and composite would be affected and, therefore, might affect the retention process.

الخلفية: تم استعمال مادة البولي-ايثر-ايثر-كيتون )البيك( في العديد من مجالات طب الأسنان. وقد تم مؤخرا اختبارها مثبتا للأسنان بعد اكمال علاجتقويم الأسنان . تهدف هذه الدراسة إلى تقييم تأثير تغيير حجم وموقع الروابط الراتنجية على أداء أسلاك التثبيت من البيك.المواد وطرق العمل :تم إجراء دراسة ميكانيكية-حيوية تضمنت أربع تصاميم ثلاثية الأبعاد للعناصر المحددة . التصميم الأساس تضمن سلكا منالبيك ذو مقطع دائري بقطر 0.8 ملم، مثبت إلى وسط السطح اللساني لتاج الأسنان الأمامية السفلى باستعمال روابط راتنجية بقطر 4 ملم. تم تصميمنموذجين بحجم روابط راتنجية 3 و 5 ملم. في حين تم تصميم النموذج الأخير بتغيير موقع الرابط الراتنجي على الناب بعيدا عن وسط السن باتجاهللقاطع الجانبي. تم تقييم الانحرافات الخطية في الاسنان، والشد في النسيج الرابط حول السني، والاجهادات في سلك البيك والروابط الرات نجية.منخلال برنامج التحليل، تم توليد البيانات وعرضها بترميز لوني. تم جدولة قيم بيانات مختارة ومقارنتها بين التصاميم المختلفة.النت ائج:كان مقدار الانحرافات الخطية صغيرا جدا. تأثرت الاجهادات في السلك والروابط الراتنجية بتغيير حجم وموقع هذه الروابط. تم تحديد حدودالأمان ب 235 ميكا باسكال لمادة البيك و 100 ميكا باسكال لمادة اللاصق الراتنجي. في التصميم الاساس، كانت قيم إجهاد فون ميسز في سلك البيكمساوية ل 122.09 ميكا باسكال، والاجهاد الاقصى الرئيسي في اللواصق الراتنجية 99.779 ميكا باسكال، ويقع كلاهما ضمن حدود الأمانللمادتين، مما يعني انخفاض مستوى خطورة فشل السلك والرابط الراتنجي في هذا التصميم. تجاوزت مستويات الاجهاد في التصاميم المتبقية حدودالأمان للروابط الراتنجية. التصميم ذو حجم روابط 3 مليمات كان الوحيد الذي تجاوزت فيه قيم الاجهادات حدود الأمان لأسلاك البيك. *الاستنتاجات: مع الاخذ بنظر الاعتبار العوامل المحددة لهذه الدراسة فإن تثبيت أسلاك البيك إلى وسط السن باستعمال روابط راتنجية بقطر 4 ملميوفر الاداء الميكانيكي الأفضل للأسلاك وللروابط، بخلافه فإن الخصائص الميكانيكية للأسلاك والروابط سوف تتأثر مما يعني التأثير على عمليةالتثبيت برمتها .الكلمات المفتاحية: التثبيت، البيك، تحليل العناصر المحددة} }