@Article{, title={Fabrication and Optimization of Electrophoretic Deposition Parameters Using Alternating Current by Taguchi Design تصنيع وتحسين عوامل الترسيب الكهربي باستخدام التيار المتناوب بواسطة تصميم Taguchi}, author={Khawla S. Khashan خولة صلاح خشان and Muhammad Jawad Issa محمد جواد عيسى and Ayad Naseef Jasim اياد نصيف جاسم and Mohammed Jasim Khadhim محمد جاسم كاظم and Muna Khethier Abbass منى خضير عباس}, journal={Al-Nahrain Journal for Engineering Sciences مجلة النهرين للعلوم الهندسية}, volume={24}, number={1}, pages={8-15}, year={2021}, abstract={The aim of this work is to optimize EPD variables (voltage, time, and focus) using alternating current through the Taguchi Design of Experiment (DOE). Coating Nano hydroxyapatite (Nano-HA) on a Ti6Al4V substrate depends on thickness and roughness, then characterization of a coating layer to determine the optimum state. Hydroxyapatite (HAp) powder was deposited on a Ti-6Al-4V alloy substrate by electro-deposition with ethanol as a solvent under AC current, to improve the alloy surface quality based on coating thickness and maximum coating mass meeting the requirements of a biological orthopedics application. Ethanol was used as a solvent to precipitate ketazone and HAp on the base alloy. Taguchi's approach was used in order to determine the optimal conditions for EPD and subsequently to apply various criteria for depositing the biochemical coating. The surface and cross-section composition of the paint is described by characterization. Numerous tests and inspections; Zeta, XRD and SEM stability test, water contact angle and optical microscopes were used to describe the surface morphology of the HAp layer. The value of the optimum conditions for deposition of the HAp layer which is a simultaneous thickness and maximum coating mass, was predicted at a sedimentation voltage of 40 V, 2 min sedimentation time and 1 g / L for the concentration of the suspended solution at room temperature. The validity of the model resulting from the response surface methodology was assessed by comparing the expected results with the experimental results. In addition, close agreement was observed between the experimental results and the expected results. For the solution at room temperature, the results obtained with the highest value of the coating thickness of 41at the surface roughness of 0.94 and the contact angle of the alloy before coating is 67.489º reduced to. 38.132º after plating, which indicates an increase in the harmony of the metal implant and biocompatibility.

الهدف من هذا العمل هو تحسين متغيرات EPD ( الجهد والوقت والتركيز) باستخدام التيار المتناوب من خلال تصميم Taguchi لتجربة طلاء Nano hydroxyapatite (Nano-HA) على الركيزة Ti6Al4V يعتمد على السمك والخشونة ، ثم توصيف طبقة طلاء لتحديد الحالة المثلى. تم ترسيب مسحوق هيدروكسيباتيت HAp) ) على ركيزة من سبيكة Ti-6Al-4V عن طريق الترسيب الكهربئي باستخدام الإيثانول كمذيب تحت تيار التيار المتردد ، لتحسين جودة سطح السبيكة بناءً على سمك الطلاء وكتلة الطلاء القصوى التي تلبي متطلبات تطبيق جراحة العظام البيولوجية. تم استخدام الإيثانول كمذيب لترسيب الكايتزون و HAp على السبيكة الاساس. تم استخدام نهج Taguchi من أجل تحديد الظروف المثلى لـ EPD وبعد ذلك تطبيق معايير مختلفة لإيداع الطلاء البيوكيميائي. تم وصف تركيبة السطح والمقطع العرضي من الطلاء بالتوصيف. العديد من الاختبارات والتفتيش ؛ تم استخدام اختبار استقرارية المحلول زيتا و XRD و SEM وزاوية تلامس الماء والمجاهر الضوئية لوصف التشكل السطحي لطبقة HAp. تم توقع قيمة الظروف المثلى لترسب طبقة HAp التي تعتبر سمكًا متزامنًا وكتلة طلاء قصوى ، عند جهد الترسيب 40 فولت ، و 2 دقيقة من وقت الترسيب و 1 جم / لتر لتركيز المحلول العالق عند درجة حرارة الغرفة. تم تقييم صلاحية النموذج الناتج عن منهجية سطح الاستجابة من خلال مقارنة النتائج المتوقعة والنتائج التجريبية. بالإضافة إلى ذلك ، لوحظ اتفاق وثيق بين النتائج التجريبية والنتائج المتوقعة. للمحلول في درجة حرارة الغرفة.النتاىئج التي تم الحصول اعلى قيمة سمك الطلاء41 µm عند خشونة سطح 0.94 كذلك زاوية التلامس للسبيكة قبل الطلاء 67.489º تقل الى 38.132º بعد الطلاء وهذا دليل على زيادة التوافقية للزوارع المعدنية.} }