@Article{, title={Evaluation of Mechanical Properties for Epoxy reinforced with palm oil /Zinc oxide composites تقييم الخواص الميكانيكية لمتراكبات الايبوكسي زيت النخيل اوكسيد الزنك}, author={Diyar J. Hassan ديار جبار حسن and Nadia A. Ali نادية عباس علي}, journal={Iraqi Journal of Physics المجلة العراقية للفيزياء}, volume={20}, number={2}, pages={26-37}, year={2022}, abstract={In this research, the effect of reinforcing epoxy resin composites with a filler derived from chopped agriculture waste from oil palm (OP). Epoxy/OP composites were formed by dispersing (1, 3, 5, and 10 wt%) OP filler using a high-speed mechanical stirrer utilizing a hand lay-up method. The effect of adding zinc oxide (ZnO) nanoparticles, with an average size of 10-30 nm, with different wt% (1,2,3, and 5wt%) to the epoxy/oil palm composite, on the behavior of an epoxy/oil palm composite was studied with different ratios (1,2,3, and 5wt%) and an average size of 10-30 nm. Fourier Transform Infrared (FTIR) spectrometry and mechanical properties (tensile, impact, hardness, and wear rate) were used to examine the composites. The FTIR results show a strong interaction between ZnO and oil palm fiber and epoxy resin. Tensile strength was reduced from 22.78 MPa to 19.03 MPa for the epoxy/OP composite as the wt% of OP was increased but increased to 29.224MPa for epoxy /oil palm / 5% ZnO samples. Young modulus increased from 1.9 MPa to 4.3 MPa while elongation decreased (9.6 to 6.8 %) with the increase of wt% OP and ZnO. The impact and hardness increased for all composites between (6.94 - 10.8 KJ/m2) and between (80.8- 84.55 KJ/m2) respectively. Also, wear resistance of the epoxy/OP and epoxy/OP/ZnO samples increased with the increase of wt% OP and ZnO. This studied in order to provide a new step in the utilization of green nanoparticle fillers for sustainable and renewable structural products for biodegradability.

يركز البحث على استخدام الايبوكسي وزيت النخيل المقطع المستخدم من نفايات الزراعة، والتي تم تشكيلها عن طريق الصب بنسب مئويه وزنيه (1، 3، 5 و 10٪ بالوزن) باستخدام المحراك ميكانيكي عالي السرعة باستخدام طريقة الصب اليدوي وتاثيرجزيئات اوكسيد الزنك النانويه (ZnO) على سلوك المتراكب مركب إيبوكسي / زيت نخيل بنسب مئويه مختلفه من جسيمات ZnO النانوية (1,2,3,5 بالوزن ٪) ذات حجم حبيبي 10-30 نانومتر. مطياف فورييه للأشعة تحت الحمراء (FTIR) ودراسه الخصائص الميكانيكية (الشد والتأثير والصلابة والتآكل) .أظهرت النتائج بان هناك تفاعل قوي بين أكسيد الزنك وألياف نخيل الزيت وراتنج الإيبوكسي، والخصائص الميكانيكيه تقل قوة الشد بين (22.78 ميجا باسكال إلى 19.03 ميجا باسكال) وترتفع إلى 29.224 ميجا باسكال لعينات الإيبوكسي / زيت النخيل / أكسيد الزنك أيضًا أن معامل ايونك ازداد بين (1.9 ميجا باسكال إلى 4.3 ميجا باسكال) مع انخفاض في الاستطالة (9.6٪ إلى 6.8٪) باضافه أكسيد الزنك. ازداد تاثير الصدمه من (6.94 إلى 10.8 كيلو جول / م2) وازدادت الصلابة بين (80.8 إلى 84.55) لجميع المتراكبات اما مقاومة التآكل لأوكسيد الإيبوكسي / OP و epoxy / OP / zinc.كذلك فان إضافة جزيئات الزنك النانوية ادت إلى زياده في مقاومه التاكل للمتراكبات النانويه. تمت دراسة خصائص مركبات الايبوكسي من أجل توفير متراكبات جديدة في استخدام الحشوات النانوية الخضراء للمنتجات الهيكلية المستدامة والمتجددة من مواد قابله للتحل.} }