TY - JOUR ID - TI - Design and Manufacturing of Anemometer for Hot Gases from available Cheap Materials AU - Ahmed H. Al-barban PY - 2022 VL - 30 IS - (2) Eng SP - 61 EP - 75 JO - Journal of University of Babylon مجلة جامعة بابل SN - 19920652 23128135 AB - This work is to build anemometer, especially for hot air or hot gas flow, from a very cheap materials available as a waste in reforming shops and small factories. The design of this tool takes in to account that any primitive technician or smith can build the tool. At the beginning, the parts of tool are designed using Catia V5R17 Software and some parts are imported to ANSYS WORKBENCH 2020 R2 software for test of mechanical stresses and deformation associated with temperature increment. Then, theoretical computations are made where angular displacement is calculated, based on equations solved by MATLAB R2020a software, where the tool faces flow air streams with different speed magnitudes. Those different air speed magnitudes used in the experiment are 1 m/s, 1.5 m/s, 2 m/s, 2.5 m/s, 3 m/s, 3.5 m/s, and 4 m/s. After that, a real tool is built and be placed in duct having a dimensions of 2 m length, 0.35m height and 0.3m width. The air flowing in that duct has the same different speed magnitudes used in theoretical computations. Then, comparison between the two results is made, which show that despite there is a relatively slide difference in angular displacement readings but the response of the real tool to the different air speed magnitudes are very coincides with the theoretical.

تم تصميم اداة قياس سرعة الغازات الحارة، التي لايمكن قياس سرعتها بالاجهزة التقليدية، من مواد رخيصة جدا متوفرة من بقايا عمليات التصنيع في الورش والمصانع الصغيرة. تم الاخذ بنظر الاعتبار اثناء التصميم ان من يقوم ببناء المفتاح هم التقنيين والحدادين المبتدئين. تم رسم أجزاء الاداة . في بداية العمل باستخدام برنامج الكاتيا، ثم تم عمل نموذج رياضي للموديل بأستخدام برناج انسس ووركبنج 2020 لفحص الاجهادات الميكانيكية المصاحبة لارتفاع الحرارة لاجزاء الجهاز وحساب مقدار التشوهات الناتجة من تلك الاجهادات بالاضافة الى حساب السماحيات الواجب تركها بين أجزاء الاداة لتجنب تلك الاجهادات. تم بعدها دراسة الموضوع نظريا لأحتساب الازاحات (الزاوية) التي تتحركها الاداة، اثناء تعرضها للهواء بأستخدام معادلات تم حلها بواسطة برنامج الماتلاب. تم اختيار سرعات هواء المختلفة لأيجاد ما يقابلها من إزاحة زاوية وتلك السرعات هي (1 , 1.5, 2, 2.5, 3, 3.5) بوحدات متر ثانية. بعد ذلك تم بناء الاداة عمليا استنادا الى النتائج والحسابات النظرية، وتم وضعها في دكت بابعاد(2 متر طول، 0.35 متر ارتفاع و 0.3 متر عرض) يمر به هواء بسرع مختلفة لمعرفة مقدار الازاحات الناتجة طبقا الى قيم السرع المختلفة. تم استخدام جهاز خاص لقياس سرعة الهواء في الدكت لتسجيل مايقابلها من ازاحة زاوية للاداة. وتمت أخيرا مقارنة النتائج النظرية والعملية وتبين هنالك فرق صغير نسبيا في قراءة الازاحات الزاوية بالإضافة الى أن تلك الاداة تستجيب بشكل جيد للتقلبات في سرعة الهواء مع جهاز قياس سرعة الهواء. ER -