@Article{, title={Fabrication of Electrospun Nanofibers Membrane for Emulsified Oil Removal from Oily Wastewater تصنيع اغشية الياف نانوية مغزولة كهربائيا لازالة النفط المستحلب من المياه الملوثة بالنفط}, author={Sura M. Alkarbouly and Basma I. Waisi}, journal={Baghdad Science Journal مجلة بغداد للعلوم}, volume={19}, number={6}, pages={1238-1248}, year={2022}, abstract={The electrospun nanofibers membranes have gained considerable interest in water filtration applications. In this work, the fabrication and characterization of the electrospun polyacrylonitrile-based nonwoven nanofibers membrane are reported. Then, the membrane's performance and antifouling properties were evaluated in removing emulsified oil using a cross flow filtration system. The membranes were fabricated with different polyacrylonitrile (PAN) concentrations (8, 11, and 14 wt. %) in N, N-Dimethylformamide (DMF) solvent resulted in various average fiber sizes, porosity, contact angle, permeability, oil rejection, and antifouling properties. Analyses of surface morphology of the fabricated membranes before and after oil removal revealed increasing the fiber size, decreasing the fouling amount, and increasing the permeate flux. On the other hand, decreasing the fiber size resulting in increases the oil rejection. It was observed that 11 wt. % PAN based nonwoven nanofiber membrane was the optimum membrane for emulsified oil removal due to its good porosity, permeability with good oil rejection. In addition, fouled nonwoven nanofiber membrane cleaning was done by backwashing technique using warm distilled water which was effective in retaining the membrane permeability and oil rejection for 7 times. The obtained results confirmed an efficient performance of the fabricated nanofibers membrane for oil-water separation with oil rejection percentage of 92.5% and a permeate flux of 120 LMH.

اكتسبت أغشية الألياف النانوية المصنعة بطريقة الغزل الكهربائي اهتمامًا كبيرًا بتطبيقات ترشيح المياه. في هذا العمل، تم تصنيع وتوصيف غشاء ألياف نانوية غير منسوج بطريقة الغزل الكهربائي. بعد ذلك، تم تقييم أداء الغشاء وخصائصه المضادة للترسبات في إزالة النفط المستحلب باستخدام نظام الترشيح القطعي. تم تصنيع الأغشية باستخدام محاليل بوليميرية ذات تراكيز مختلفة من البولي أكريلونيتريل (PAN) (8,11,14%) المذاب في N-N-Dimethylformamide (DMF) ونتج عنه معدل أحجام مختلفة من الألياف ، والمسامية ، وزاوية التلامس ، والنفاذية ، وفصل النفط ، و خصائص مضادة للترسبات. أظهرت تحليلات التشكل السطحي للأغشية المصنعة قبل وبعد إزالة النفط كبر حجم الألياف وتقليل كمية الترسبات وزيادة تدفق النفاذية. من ناحية أخرى، يؤدي تقليل حجم الألياف إلى زيادة فصل النفط. لوحظ أن غشاء الألياف النانوية غير المنسوج المصنع من 11% PAN/DMF هو الغشاء الأمثل لإزالة النفط المستحلب بسبب مساميته الجيدة ونفاذه مع قابلية فصل جيد للنفط. بالإضافة إلى ذلك، تم تنظيف أغشية الألياف غير المنسوجة المستخدمة للترشيح مسبقا بواسطة تقنية الغسيل العكسي باستخدام الماء المقطر الدافئ والتي كانت فعالة في الحفاظ على نفاذية الغشاء وقابلية فضل الزيت لمدة 7 مرات. النتائج تثبت الكفاءة الجيدة لغشاء الالياف النانوية المصنعة لإزالة النفط من الماء بنسبة ازالة نفط تصل الى 92.5% ومعدل جريان 120 LMH} }