@Article{, title={Finite Element Modeling and Simulation of Orthogonal Cutting With Multi Layer Coated Tools}, author={Maan Aabid Tawfiq and Zeena jumaa Ahmed}, journal={Engineering and Technology Journal مجلة الهندسة والتكنولوجيا}, volume={26}, number={7}, pages={829-841}, year={2008}, abstract={This paper focuses on the development of Finite Element Method (FEM) inmodeling and simulation of coated cutting tools with multi-layer coats. A special FiniteElement code called (MSC.MARC mentat) is used in the numerical tests, the results arethen compared with experimental work. The paper studied the effect of number of coatsof cutting tools on the following field parameters; tool-chip contact length, chipcontraction coefficient and shear angle at similar machining conditions.The metal beingmachined is (AISI 1045 steel) with orthogonal machining conditions. The three cuttingtools and models are coated with (TiN, TiN/TiC, TiN/Al2O3/TiC), while the fourth oneis uncoated.The results show good agreement between the experimental and numericaltests. Some of the results are compared with other published papers. The comparison ofthe predicted results shows good agreement with experimental tests with maximumrelative difference of (18%) for the chip contraction coefficient and contact length, and(10 %) for the shear angle. The insert with double coats shows excellent result,compared to others from point of view of chip contraction coefficient, contact length andshear angle.

في هذا البحث دراسة تأثير عدد طبقات الطلاء لعدة القطع على كل من: معامل إنكماشطول منطقة التماس بين وجه العدة ،(chip contraction coefficient ) النحاتةوذلك تحت متغيرات تشغبل ، (shear angle) وزاوية القص (tool-chip contact length) والنحاتةFinite ) ثابتة من سرعة قطع وعمق قطع وتغذية، حيث تضمن البحث استخدام تقنية العناصر المحددة.(AISI في نمذجة ومحاكاة النتائج والمقارنة عند تشغيل معدن صلب ( 1045 (Element MethodTiN/TiC وTiN) : استخدمت ثلاثة أنواع من مواد الكساء للعدة منها: المكسية بكل من المواد التاليةفي حين كانت العدة الرابعة غير مكسية. وقد استخدم برنامج حاسوبي (TiN/Al2O3/TiC وفي الجانب التحليلي للبحث وذلك لمقارنة النتائج التي تم التوصل (MSC.MARC) متخصص يدعىاليها في الجانب العملي. أظهرت النتائج قيمًا متقاربة للجانبين العملي والتحليلي كما وأظهرت كذلكتوافقًا مع بعض النتائج المنشورة لباحثين آخرين في هذا المجال، وبينت النتائج بان أكبر فرق بين% النتائج العملية والتحليلية لمعامل إنكماش النحاتة وطول منطقة التماس يصل إلى 18 % ‚ و 10لزاوية القص. كما وجد بان عدة القطع المكسية بطبقتين هي المثلى من ناحية طول منطقة التماس بينوجه العدة والنحاته، زاوية القص ومعامل إنكماش النحاتة} }