TY - JOUR ID - TI - دراسة تأثير اضافة كل من كاربيد السليكون وكاربيد البورون في سلوك الكلال لسبيكة (Al-Si-Mg) AU - سرمد عماد ابراهيم حسين PY - 2008 VL - 26 IS - 12 SP - 484 EP - 495 JO - Engineering and Technology Journal مجلة الهندسة والتكنولوجيا SN - 16816900 24120758 AB - The presnt research had dealt with preparation of bars with length of about (13Cm)and a diameter of (1.5Cm) of composite material with metal matrix represented by(Al-Si-Mg) cast reinforced by (SiC) or (B4C) particles with choosen weightpersentages (0.2,0.6,1%). The matrix alloy and the composite materials wereprepared by casting methode and using vortex technique in order to dispersreinforced prticles in homogeneous way on the matrix alloy floor. In addition tothat, two main groups of composite materials, the first group included compositematerial reinforced by (SiC) particles represented by the particle size(30μm≥p.size≥0.1μm) while the second group included composite materialreinforced by (B4C) particles represented by the particle size(25μm≥p.size≥0.1μm).Concerning test that were made for the prepared models, they included fatigue testto either matrix alloy and product composite material. The study contained theeffect of solution heat treatment at (520C ْ) for (1hr) and the following formingprocess in addition to double aging process were made for the prepared model offatigue test and included the aging at (150C ْ) for (2hr) and then aging at (170C (ْduring different periods.Results of fatigue test showed an increase in fatigue resistance in addition to theincrease in reinforced particles that were added, but staying at higher values thanthat in the matrix alloy, The effect of type for reinforced particles in this propertywas noted, There was a specified increase in fatigue resistance of compositematerial reinforced by (B4C) particles in comparasion with the reinforced by (SiC)particles. Their values were more than in the matrix alloy.

1.5 ) من مواد متراكبة ذات Cm) 13 ) وقطرها Cm) تناول البحث الحالي تحضير قضبان طولهامن جهة ودقائق (SiC) مقواة بدقائق كاربيد السليكون (Al-Si-Mg) اساس معدني تمثل بسبيكةمن جهة اخرى وبنسب وزنية مختار ة (% 0.2,0.6,1 ). حضرت (B4C) كاربيد البورون(Vortex Technique) سبيكة الاساس والمادة المتراكبة بطريقة السباكة بأستخدام تقنية الدوامةلتشتيت دقائق التقوية في ارضية سبيكة الاساس، وقد تم تحضير مجموعتين رئيستين منمادة (a) الموادالمتراكبة بالاعتماد على نوعية مواد التقوية، حيث تضمنت المجموعة الاولى(30μm≥p.size≥0.1μm) متراكبة مقواة بدقائق كاربيد السليكون والمتمثلة بالاحجام الحبيبيةمادة متراكبة مقواة بدقائق كاربيد البورون والمتمثلة بالاحجام (b) بينما تضمنت المجموعة الثانية.(25μm≥p.size≥0.1μm) الحبيبيةاما الفحص الذي اجري على النماذج المحضرة فقد تمثل بفحص الكلال لكل من السبيكة الاساسوالمادة المتراكبة المنتجة، وتضمنت الدراسة ايضُا تأثير المعاملة الحرارية المح لولية عند520 ) مدة ساعة واحدة وعملية التشكيل اللاحقة فض ُ لا عن عملية التعتيق المزدوجة C°) درجة(150C°) التي اجريت على النماذج المحضرة لفحص الكلال والمتمثلة بالتعتيق الاولي عند درجة170 ) خلال فترات مختلفة. C°) مدة ساعتين ثم تبعها تعتيق عند درجةولقد بينت نتائج فحص الكلال زيادة مقاومة الكلال مع زيادة نسب دقائق التقوية المضافة. حيثتبقى عند قيم اعلى مما هي عليه في السبيكة الاساس، اما تأثير نوعية دقائق التقوية في تلكالخاصية فقد لوحظ ان هنالك زيادة ملحوظة في قيم مقاومة الكلال بالنسبة للمادة المتراكبة المقواةبدقائق كاربيد البورون مقارنة مع المادة المتراكبة المقواة بدقائق كاربيد السليكون والتياكتسبت قيمَاً اعلى مما هي عليه في السبيكة الاساس. ER -