@Article{, title={Effect of Sintering Temperature on Some Physical And Mechanical Properties of Fabricated Hydroxyapatite Used For Hard Tissue Healing تأثير درجة حرارة التلبيد على بعض الخصائص الفيزياويه والميكانيكيه للهيدروكسي اباتاتيه المصنع والمستخدم لمعالجه الانسجه الصلبه}, author={Payman Suhbat Ahmed and Waleed Asim Hanna and Kahtan khalaf Al-Khazraji}, journal={Engineering and Technology Journal مجلة الهندسة والتكنولوجيا}, volume={28}, number={10}, pages={1880-1892}, year={2010}, abstract={This work focuses on studying the role of drying and calcination onstiochiometry and crystallinity of deposited HA. Also, studying the effect of sinteringtemperature on phases generated, physical and mechanical properties of sintered HApowder compact at a range of (800-1200) ˚C.Both Ca/P ratio and crystallinity were increased after calcination, where the Ca/Pratio raised from 1.7 to 1.9 and the height of Hydroxyapatite peak intensity was alsoincreased .Secondary phases also appeared.X-ray diffraction patterns and electrical microscopic pictures of polished surfacesof the Hydroxyapatite compact after sintering had revealed the process ofdensification and crystallization of Hydroxyapatite . The increase of sinteringtemperature leads to grain growth, while surface cracking and other defects becamelower i.e. porosity and surface voids.Both hardness and fracture strength were increased for samples sintered at hightemperatures where they reached their maximum values at sintering temperature(1200)ºC .The maximum linear shrinkage was 20% at sintering temperature 1200ºC.The maximum bulk density was (2.173) g/cm3 at sintering temperature of 1200ºCand the maximum apparent density was (2.58) g/cm3 at sintering temperature 900ºC.The maximum apparent and open porosities were 47.136% and 47.058% respectivelyat sintering temperature 900ºC. The maximum water absorption was 39.13% atsintering temperature 800ºC.

يركز هذا البحث على دراسة دور عمليتي التجفيف و الكلسنة على التوازن الكيميائي وتبلور الهيدروكسي اباتايت المحضر . وكذلك دراسة تأثير درجة حرارة التلبيد على الأطوار المتكونة و الخواص الفيزياوية و الميكانيكية لمسحوق الهيدروكسي اباتايت المكبوس و الملبد ضمن م. º(1200- المدى ( 800P Ca بعد عملية الكلسنة , حيث تزداد نس بة P Ca لوحظ ازدياد كل من التبلورية و نسبة من 1.7 إلى 1.9 بالإضافة إلى ازدياد ارتفاع شدة قمة الهيدروكسي اباتايت و ظهور الأطوارالثانوية.أظهرت مخططات الأشعة السينية و صور المجهر الضوئي للسطوح المكبوسة و المصقولة بعد التلبيد ، عملية التبلور و التكثف للهيدروكسي اباتايت . أدت الزيادة في درجة حرارة التلبيد إلى النمو الحبيبي كما تراجعت الشقوق السطحية و العيوب الأخرى (المسامات والفجوات السطحية). ازداد كل من الصلادة و مقاومة الكسر للنماذج الملبدة في درجات الحرارة العالية حيث تصل م. º( إلى أعلى قيمها عند ( 1200 م أعلى قيمة º ( أعلى قيمة للتقلص الخطي كانت ( 20 )% عند درجة حرارة تلبيد ( 1200 م . أعلى قيمة للكثافة º( للكثافة الكتلية كانت( 2.173 ) غمسم 3 عند درجة حرارة تلبيد( 1200 م وأعلى قيمة للمسامية المفتوحة و º ( الظاهرية كانت( 2.58 ) غمسم 3 عند درجة حرارة( 900 م ،و º ( الظاهرية كانت ( 47.058 )% و ( 47.136 )% على التوالي عند درجة حرارة تلبيد ( 900 م. º( أعلى قيمة لأمتصاصية الماء كانت ( 39.13 ) %عند درجة حرارة تلبيد( 800} }