TY - JOUR ID - TI - Agent Based Monitoring For Investigation Process And Maintenance Improvement AU - Soroor K.Hussain AU - Zouhair I. Ahmed AU - Ameer Hussein Ali PY - 2011 VL - 17 IS - 5 SP - 1269 EP - 1288 JO - Journal of Engineering مجلة الهندسة SN - 17264073 25203339 AB - Agent technology has a widespread usage in most of computerized systems. In this paper agent technology has been applied to monitor wear test for an aluminium silicon alloy which is used in automotive parts and gears of light loads. In addition to wear test monitoring, porosity effect on wear resistance has been investigated. To get a controlled amount of porosity, the specimens have been made by powder metallurgy process with various pressures (100, 200 and 600) MPa. The aim of this investigation is a proactive step to avoid the failure occurrence by the porosity.A dry wear tests have been achieved by subjecting three reciprocated loads (1000, 1500 and 2000)g for three periods (10, 45 and 90)min. The weight difference after each test is immediately measured to find the losing weight and wear rate for each specimen. Wear test was monitored online by two sensors, force sensor to control the applied load, find friction force and coefficient of friction. The sensor is an acoustic emission to detect crack initiations of the worn surface by transfers the emitted ultrasonic waves from crack initiations to electric signals. Scanning electron microscope has been used to examine the worn surfaces. The overall results include that the effect of pores depends on pore shapes, sizes and concentrations.

تقنية العميل لها استخدام واسع في معظم الأنظمة المسيطر عليها بواسطة الحاسوب. في هذا البحث تم تطبيق تكنلوجيا العميل لمراقبة فحص البليان لسبيكة الأمنيوم سليكون التي تدخل في صناعة اجزاء السيارات ومنتجات اخرى كتروس اللأحمال الخفيفة. بالاضافة الى مراقبة فحص البلي, تم التحقيق من تأثير المسامية على مقاومة البليان. للحصول على كمية مسيطر عليها من المسامية تم تصنيع العينات بواسطة عملية مساحيق المعادن مع ضغوطات متغيرة (100, 200 و600) ميكا باسكال. الهدف من هذا الفحص هو الخطوة الاستباقية لتجنب حدوث الفشل الناتج من المسامية.اختبارات البلي الجاف قد انجزت عن طريق تسليط ثلاثة احمال تبادلية (1000, 1500 و2000) غم لثلاث فترات (10, 45 و 90) دقيقة. تم قياس الفارق بالوزن مباشرة بعد اختبارات البلي الجاف قد انجزت عن طريق تسليط ثلاثة احمال تبادلية (1000, 1500 و2000) غم لثلاث فترات (10, 45 و 90) دقيقة، وتم قياس الفارق بالوزن مباشرة بعد كل عملية فحص لإيجاد فقدان الوزن ومعدل البلي لكل عينة. اما فحوصات البلي تم مراقبتها بصورة مباشرة بواسطة متحسسين، احدهما متحسس القوى واستخدم لضبط الحمل المسلط ، ايجاد قوة الإحتكاك و معامل الاحتكاك. اما المتحسس الاخر هو متحسس الانبعاثا ت الصوتية لكشف بدايات التصدع في السطح المبلي عن طريق تحويل الموجات فوق الصوتية المنبعثة من بداية التصدع الى اشارة كهربائية. تم استعمال المجهر الماسح الألكتروني لفحص السطوح البالية. تضمنت النتائج بشكل اساس ايجاد تأثير المسامية على مقاومة البليان الذي يعتمد على شكل وحجم وتراكيز المسامات على في المعدن ER -