@Article{, title={Effect of partial heat treatment on the mechanical properties of high carbon tool steel used in manufacturing active parts in cold work tool steel dies تأثير المعاملة الحرارية الجزئية على الخواص الميكانيكية لصلب العدة عالي الكربون المستخدم في صناعة الأجزاء الفعالة لقوالب القطع على البارد}, author={نيفين جمال الونداوي}, journal={Engineering and Technology Journal مجلة الهندسة والتكنولوجيا}, volume={27}, number={5}, pages={181-189}, year={2009}, abstract={Effect of partial heat treatment on the mechanical properties of high carbon tool steel used in manufacturing active parts in cold work tool steel dies was investigated in this work. High carbon alloy steel (X210Cr12) classified as(QN1.2080) according to (DIN) was used for machining specimens withdimensions (5×44×20mm).(18) specimens were insulated from the middle to the end by graphite with (5mm)thickness and (18) specimens were insulated by ceramic (Al2O3 + Kaolin) with(5mm) thickness. The distance between the middle to the sharp edge was notinsulated. All these specimen were subjected to heat treatment, They show that canobtain hardness (65HRC) for the sharp edge at (980oC) after the specimens werequenched in oil. Stress relive was subjected to all specimens , it has been shownduring heating between (100-200oC) There is no big effect on the hardness and thestrength was increased, also when heating temperature increase up to (600 C ) thehardness decrease at (30 HRC) .Rockwell hardness test was employed to all specimens, at four locationsfor each specimen. The first location is at distance (10mm) from the sharp edge andthe second at (20mm) from the sharp edge within un insulated part. The thirdlocation is at (30mm) and the forth at (40mm) from the sharp edge withininsulated part.The best values of hardness for the insulated specimen with graphite are(65,64HRC) within the un insulated part and (47,48 HRC) within the insulatedpart. For the specimen with ceramic insulation the hardness values are (65,64HRC) within the un insulated part and (51,52 HRC) within the insulated part.The results of this work was applied on the active parts of some pressworking sheet metal dies, produced in central tool room plant/Nasser statecompany, it has been shown that the life and fracture strength of these parts (punch,die and stripper) were increased and improved.

تم اجراء الم عاملة الحرارية الجزئية ودراسة تاثيرها على الخواص الميكانيكية لصلب(X210Cr العدة عالي الكربون في هذا البحث . استخدمت سبيكة الفولاذ عالي الكربون نوع ( 12الالماني في تشغيل عينات بابعاد (DIN) والمصنفة بالرقم ( 1.2080 ) حسب نظام ال5) ملم تم عزل العينات من المنتصف بواسطة نوعين من غلاف عازل، اذ تم عزل ×44×20)18 ) عينة بواسطة غلاف من الكرافيت بسمك ( 5ملم)، وعزلت ( 18 ) عينة اخرى بواسطة )غلاف من مادة سيراميكية (الومينا+كاؤولين) بسمك ( 5 ملم )، واجريت المعاملة الحرارية للسطحبالتسخين التدريجي، اذ تبين عند ((Sharp edge) الغيرمعزول (من المنتصف الى الحد القاطع65 ) بعد HRC) 980 ) يتم الحصول على اعلى قيمة للصلادة oC) التسخين الى درجة حرارةوتمت دراسة عملية ازالة الاجهادات (Quenching in oil) اجراء عملية الاخماد بالزيت100-200 ) لم يطرأ تغيير oC) اذ تبين عند التسخين الى درجة حرارة مابين (Stress relives)كبير على قيمة الصلادة وادت العملية الى زيادة المتانة بشكل ملحوظ . وانخفضت الصلادة الى.(600oC) 30 ) عند التسخين الى درجة حرارة HRC) ادنى معدل لها وهيلعينات البحث حيث تم تحديد اربع نقاط على (HRC) اجري اختبار صلادة روكويلسطح كل عينة، تبعد ال نقطة الاولى بمسافة ( 10 ملم ) عن الحد القاطع والنقطة الثانية ( 20 ملم )عن الحد القاطع ضمن السطح الغير معزول والنقطة الثالثة ( 30 ملم) والنقطة الرابعة ( 40 ملم )عن الحد القاطع ضمن السطح المعزول.65,64 )، من الحد القاطع الى المنتصف ضمن السطح الغير HRC) وسجلت قيم الصلادة48,47 ) ضمن السطح المعزول بالنسبة للعينات المعزو لة بغلاف كرافيتي . اما HRC) معزول، و65,64 ) من الحد القاطع الى HRC) العينات المعزولة بغلاف سيراميكي فقد سجلت قيم الصلادة51,52 ) من المنتصف الى نهاية العينة ضمن السطح HRC) المنتصف للسطح الغير معزول والمعزول. تم ملاحظة تقارب قيم الصلادة للعينات المعزولة بغلاف كرافيتي والعينات المعزولةبغلاف سيراميكي.تم اجراء المعاملة الحرارية الجزئية الذي تم التوصل اليها من خلال البحث للأجزاء الفعالة (ذكرلقوالب القطع والقوالب المرحلية التي ينتجها معمل القوالب والعدد (Punch &Die وانثى القالبالمركزي/شركة نصر العامة للصناعات الميكانيكية، حيث تم ملاحظة زيادة عمر الاجزاءالمذكورة وزيادة مقاومتها للكسر تحت ظروف العمل المختلفة.} }