@Article{, title={Effect of Heat Treatments on The Mechanical Properties And Wear Resistance of Al- Alloy Matrix Composite تأثير المعاملات الحرارية على الخواص الميكانيكية ومقاومة البلى لمادة مركبة ذات أساس المنيوم}, author={منى خضير عباس and ايمان خليل أبراهيم and ايمان صبيح نعيم}, journal={Engineering and Technology Journal مجلة الهندسة والتكنولوجيا}, volume={29}, number={12}, pages={518-533}, year={2011}, abstract={Metal matrix composite (MMCs) of the base alloy (Al-0.978%Mg-1.03%Si) reinforcedwith SiC particles (10 wt %) with particle size (53-106) μm was prepared by stir castingusing vortex technique. Solution heat treatment and aging are carried out at a constanttemperature of 175C° for different aging times. Many inspections and tests such asmicrostructure, Vickers hardness and XRD analysis. Wear test type ( Pin – on – Disc) withvarious applied loads and different exposure times at constant parameters was carried outunder dry sliding conditions.It was found that the addition of SiC particles to base alloy improved the hardness andwear resistance before and after heat treatment (precipitation hardening).In addition, using SiC particles with alloy matrix resulted in a faster aging response i.e thetime of peak hardness decreased from 8hr to 5hr for base alloy and composite respectively.These results indicate that the addition of SiC particles to Al –alloy matrix accelerates theaging kinetic.

(Al – 0.978% Mg – 1.03% Si) تم تحضير مادة مركبة معدنية ذات اساس من سبيكة53 ) بطريقة السباكة – 106) μm وبنسبة (% 10 ) وذوحجم حبيبي (SiC) مقواة بدقائق كاربيد السيلكونبالتحريك باستخدام تقنية الدوامة. واجريت عملية المعاملة الحرارية (المعاملة المحلولية والتعتيق) عند175 ولفترات تعتيق مختلفة. وقد اجريت عدة فحوصات واختبارات منها فحص البنية C◦ درجة حرارةالمجهرية وفحص الصلادة الفيكرزية والفحص بحيود الاشعة السينية .وكذلك أجري أختبار البلى الانزلاقيباستعمال احمال متغيرة وازمان تعرض مختلفة مع ثبوت العوامل (Pin –on- Disc) الجاف نوعالاخرى.الى السبيكة الاساس ادى الى تحسين الصلادة ومقاومة البلى قبل وبعد (SiC) وقد لوحظ ان اضافة دقائقالى أرضية السبيكة (SiC) اجراء المعاملة الحرارية (الاصلاد بالترسيب). وكذلك لوحظ ان اضافة دقائقوتقليل زمن التعتيق اللازم (Mg2Si) ادى الى تعجيل عملية التعتيق وترسيب دقائق الطور الثاني5 بالنسبة للسبيكة الاساس والمادة المركبة على hr 8 الى hr للوصول الى قيمة الصلادة العظمى منالتوالي.} }