TY - JOUR ID - TI - Reliance on Ground Coordinate Measurements Produced by DGPS Post-Processing اعتماد الاحداثيات الارضية الناتجة من جهاز ال DGPS بعد معالجتها AU - Abdul Razzak.T.Ziboon AU - Lubna.AL-Shammari PY - 2012 VL - 30 IS - 5 SP - 697 EP - 709 JO - Engineering and Technology Journal مجلة الهندسة والتكنولوجيا SN - 16816900 24120758 AB - Some users of the GPS take the coordinates and the distances between points as they are in the field and try to joint work with the total station, but they found a difference between the coordinates and the distances. The reason is that these measurements are three-dimensional Coordinates: where they are represented on the model of the Earth,while the total station based on the theory of plan survey are two-dimensional coordinates. And other causes the distortion resulting from the projection itself. From the scientific point of view, all the solutions applied for this problem are not accurately enough, but serve their purpose. Where as in this research we are trying to cancel the differences in the coordinates and the distances between the GPS and the total station measurements. Where work on a project using both techniques (GPS, and Total station) .The coordinates of the project are measured on the site by considering the total length of the project (35km) and ten control points as base line points had been distributed along the route including the X and Y coordinates corresponding to the zone 38N. It was found that the DGPS Software (Topcon Tools v7) or other data collection software can be used to convert the coordinates from grid coordinates to ground coordinates and then these coordinates can be used with the total station in the field for small distances. But for large distances the ground coordinates that obtained from Total station instrument must be used to avoid accumulative error. And must also take into account when choosing sites of the control network in the field where it should be direct view between the control network points to get rid of random errors resulting from the use total stationthis in turn leads to obtain high accuracy results for the ground coordinates.

يستخدم الاحداثيات الناتجة او المسافات GPS بعض مستخدمي نظام ايجاد الاحداثيات العالمي ال station باستخدام جهاز ال Total station بين النقاط كما هي ويحاول العمل بها مباشرة فيلاحظ فرق بين الاحداثيات او المسافات والسبب في ذلك يعود على ان هذه القياسات تعتبر ثلاثية Total يعمل على Total Station على مجسم الارض بينما جهاز ال Three Dimensional الابعاد اضافة الى التشوه Two Diensional اساس مبادئ المساحة المستوية او الاحداثيات ثنائية الابعاد الناتج عن الاسقاط ذاته. اما حلول هذه المشكلة فهي حلول تطبيقية . حيث تم التوصل الى طريقة تحاول الغاء حيث تم . Total station وال GpS الفرق في الاحداثيات والمسافات بين ال وعددها Base Line العمل في مشروع يستعمل كلا التقنيتين حيث تم تثبيت نقاط خط القاعدة ال 10 نقاط موزعة على طريق طوله 35 كم والذي يمثل خط سكة يربط بين مدينتي المسيب DGPS وكربلاء والتي تمثل منطقة المشروع باستخدام جهاز قياس الحداثيات التفاضليالذي ستخدم للتاكد من صحة الاحداثيات الارضية. Total station وجهاز الحيث تم التوصل الى امكانية استخدام برامجيات الى Grid Coordinate لتحويل الاحداثيات من ال DGPS software Topcon Tools V7 واستخدام هذه الاحداثيات الارضية في المشاريع ذات المساحات الصغيرة Grid Coordinate بينما في المشاريع الطولية مثل خطوط سكة او انابيب او شبكة طرق فيجب استخدامالاحداثيات الارضية المقاسة بواسطة جهاز المحطة الكاملة وكذلك يجب الاخذ بنظر الاعتبار عند اختيار نقاط السيطرة ان يكون بينها مجال رؤيا واضح للتخلص من الاخطاء العشوائية وهذا بدوره يؤدي الى الحصول على نتائج Total station الناتجة من استخدام جهاز ال عالية الدقة بالنسبة الى الاحداثيات الارضية. ER -