TY - JOUR ID - TI - Theoretical and Experimental Investigation of Transient Temperature Distribution in Friction Stir Welding of AA 7020-T53 AU - Muhammed Abdul-Sattar AU - Moneer Hameed Tolephih AU - Muhsin Jaber Jweeg PY - 2012 VL - 18 IS - 6 SP - 693 EP - 709 JO - Journal of Engineering مجلة الهندسة SN - 17264073 25203339 AB - Finite element modeling of transient temperature distribution is used to understand physical phenomena occurring during the dwell (penetration) phase and moving of welding tool in friction stir welding (FSW) of 5mm plate made of 7020-T53 aluminum alloy at 1400rpm and 40mm/min. Thermocouples are used in locations near to the pin and under shoulder surface to study the welding tool penetration in the workpiece in advance and retreate sides along welding line in three positions (penetrate (start welding) , mid, pullout (end welding)). Numerical results of ANSYS 12.0 package are compared to experimental data including axial load measurements at different tool rotational speeds (710rpm.900rpm.1120rpm and 1400rpm) Based on the experimental records of transient temperature at several specific locations of thermocouples during the friction stir welding process the temperatures are higher on the advancing side (629.2oK) than the retreating side (605 oK) along welding line and temperature in the top of workpiece under tool shoulder is higher(645 oK) than bottom (635.79oK).The results of the simulation are in good agreement with that of experimental results. The peak temperature obtained was 70% of the melting point of parent metal.

موديل رياضي بطريقة العناصر المحددة استخدم لتمثيل التوزيع الحراري العابروفهم الظواهر الفيزياوية التي تحدث اثناء عملية الغرز (دخول) و حركة اداة اللحام في عملية اللحام بطريقة اللخلط الاحتكا ك لصفيحة من سبيكة الالمنيوم(7020-T53)بسمك 5 ملم عند( سرعة دورانية 1400rpm,سرعة خطية40mm/min ). النتائج النظرية باستخدام ANSYS 12.0) )قورنت مع النتائج العملية متضمنة قياس الحمل العمودي عمليا لعدة سرع دورانية (1400rpm,1120rpm 900rpm, ,(710rpmفي هذا العمل تم استخدام مزدوجات حرارية وضعت في مواقع قريبة من راس اداة اللحام (pin) وتحت (shoulder) لغرض دراسة عملية دخول وكيفية توزيع الحرارة على جانبي وتحت اداة اللحام و لثلاث مناطق من الصفيحة (منطقة الغرز ,وسط, نهاية اللحام (خروج اداة اللحام).بالاعتماد على النتائج العملية المسجلة للتوزيع الحراري العابر عند مواقع مختلفة للمزدوجات الحرارية على جانبي اداة اللحام خلال عملية اللحام الخلط الاحتكاك وجد ان درجة الحرارة في منطقة (629.2 oK advance)هي اعلى من منطقة (retreate 605 oK)على طول خط اللحام كما ان الحرارة عند سطح العينة تحت (shoulder 645 oK)هي اعلى من اسفل العينة (635.79oK),اقصى حرارة سجلت كانت 70% من درجة الانصهار للسبيكة الامنيوم .نتائج الموديل الرياضي كانت متوافقة مع النتائج العملية. ER -