TY - JOUR ID - TI - Estimating The Limits of Stability under Several Working Conditions at Experimental Turning تخمين حدود الاستقرارية تحت ظروف عمل متعددة خلال عملية الخراطة عمليا AU - Ramiz Saeed Matty Samarjy رامز سعيد سمرجي PY - 2009 VL - 17 IS - 6 SP - 77 EP - 91 JO - AL-Rafidain Engineering Journal (AREJ) مجلة هندسة الرافدين SN - 18130526 22201270 AB - AbstractPredicting the Self-Excited vibrations (Chatter) during the cutting process as a result of the interaction between the cutting tool and work - piece is important as a guide for the cutting machine user for an optimal selection of the back engagement of tool in work piece(depth of cut), the rotational Speed for the specific feed rate which will produce maximum chip removal with out these undesirable vibrations. Such undesirable vibrations can spoil the cutting surface with chatter marks, which will have adverse effects on the whole cutting system. This can be achieved by performing several experimental researches. In the present study, a cutting process was performed by using the slide feeding of Hindustan lathe machine and sintered carbide inserts to cut several cylindrical shafts of 32 mm in diameter and 70cm long steel AISI1050 with out using coolant lubrication to specify the stability limits that represented by curves with the rotational speeds which separate stable and unstable zones for maximum productivity and accepted surface roughness. Also study the effect of feed rate upon the stability and the amplitude of vibration for constant depth of cut and rotational speed.Key words : stability limit , chatter vibration , self excited vibration

الخلاصة تحديد الاهتزازات الناشئة تلقائيا( الاصطكاك) أثناء عملية القطع نتيجة للتداخل بين أداة القطع )قلم الخراطة( وبين القطعة المشغولة يعتبر مهما كمرشد لمستخدم ماكنة القطع للاختيار الامثل لعمق القطع والسرعة الدورانية لمعدل التغذية المعني ، الذي سوف يحقق أقصى معدل إزالة للرايش من دون حدوث هده الاهتزازات الغير مرغوب فيها والتي تفسد السطح المشغول باثارها وتنعكس سلبا على نظام القطع ككل. وهدا يمكن تحقيقة بأجراء عدد من البحوث العملية. في هده الدراسة تم أجراء عملية القطع باستخدام الخراطة الطولية لمكنة الخراطة نوع هندستون وباستخدام قطع كاربيدية لقطع عدة قطع اسطوانية مشغولة من الصلب متوسط الكاربون ذات قطر 32 ملم وطول 70سم بدون استخدام سائل تبريد لتحديد حدود الاستقراية التي مثلت بواسطة منحنيات مع السرعة الدورانية والتي فصلت مابين المساحات المستقرة والغير مستقرة باعتبارها الحد الفاصل ولعدة معدلات تغذية والتي حققت أعظم إنتاجية مع خشونة سطحية مقبولة بغياب الاهتزازات الاصطكاكية. وكذلك تمت دراسة مدى تأثير معدل التغذية على استقرارية نظام القطع وعلى سعة الاهتزاز بثبوت عمق وسرعة القطع . الكلمات الدالة : حد الاستقرارية ، الاهتزازات الناشئة تلقائياً ، الاصطكاك ER -