TY - JOUR ID - TI - Study of Dry Sliding Wear Behavior of Al-12%Si alloy Produced By Squeeze Casting دراسة سلوك البلى الأنزلاقي الجاف لسبيكة الألمنيوم-12 %سليكون المنتجة يطريقة السباكة بالعصر AU - Dr.Muna Khedier Abbass * أ.م.د.منى خضير عباس* أ.م.د.منى خضير عباس* PY - 2009 VL - 9 IS - 3 SP - 369 EP - 382 JO - Iraqi journal of mechanical and material engineering المجلة العراقية للهندسة الميكانيكية وهندسة المواد SN - 20761819 AB - The present research deals with study of the effect of applied casting pressure at constant pouring and die preheating temperatures on the microstructure and dry sliding wear behavior of the squeeze cast Al-12%Si alloy was investigated. A pin-on-disc tests were conducted at varying loads from 5 to 20 N and a sliding speed of 2.7m/sec for a constant sliding time of 20min. The results showed that a refinement in the microstructure with increasing the squeeze pressure. The results showed that the wear rates and coefficient of friction ( μ ) of the squeeze cast samples are lower than that of the gravity die cast sample. The results also showed that the density of the specimens decreased with application of a 7.5 MPa applied pressure, but it increased steadily for higher pressures up to 53 MPa. Increasing the squeeze pressure resulted in increasing the hardness and decreasing the wear rate. These results were explained based on the densification mechanism brought about by the application of pressure during solidification.

يتناول هذا البحث دراسة تاثير ضغط السباكة المسلط عند درجات حرارة صب وتسخين مسبق لقالب الصب ثابتة على التركيب المجهري وسلوك البلى الأنزلاثي الجاف لسبيكة الالمنيوم –12% سليكون المنتجة بطريقة السباكة بالعصر. وأجريت أختبارات البلى من نوع المسمار على القرص عند أحمال متغيرة من 5 -20 نيوتن وسرعة أنزلاق 2.7 متر/ثانية ولفترة زمنية ثابتة 20.دقيقة. واظهرت النتائج حصول تنعيم في البنية المجهرية مع زيادة ضغط السباكة. اظهرت النتائج أن معدلات البلى ومعامل الأحتكاك ( μ ) للنماذج المنتجة بطريقة السباكة بالعصرأقل مما هو عليه في حالة النموذج المنتج يطريقة السباكة بالجاذبية. واظهرت النتائج ايضا بان كثافة العينات قد قلت عند تطبيق ضغط مسلط مقداره (7.5MPa), لكنها قد زادت بصورة ثابتة عند تسليط ضغوط اعلى الى حد (53MPa). ان زيادة ضغط السباكة ادت الى زيادة الصلادة وتقليل معدل البلى. ان هذه النتائج قد تم تفسيرها بالاعتماد على الية زيادة الكثافة الناتجة بواسطة تطبيق الضغط اثناء التجمد. ER -