@Article{, title={Drilling of FR-4 Composite Materials Using Single Pulse of Nd:YAG Laser تثقيب المادة المركبة (فايبر كلاس) باستخدام النبضة المفردة لليزر النيدميوم – ياك}, author={Amer G. Hoss عامر غازي هوس and Enas A. Khalid ايناس عبد الكريم خالد and Osamah F. Abdulateef اسامة فاضل عبد اللطيف}, journal={Al-Khwarizmi Engineering Journal مجلة الخوارزمي الهندسية}, volume={9}, number={2}, pages={1-11}, year={2013}, abstract={Laser drilling is capable of producing small, precisely positioned holes with high degree of reproductively. In this paper , IR millisecond Nd:YAG single pulsed laser was used to determine the effect of laser parameters on the drilled hole of the glass - fiber reinforced epoxy composite FR-4 sample of 2 mm in thickness . The type of laser source was GSI lumonics JK760TR Series laser 1.064μm system in a CNC cabin. The JK760TR series has a 0.3-50ms pulse length and a maximum repetition rate 500Hz with an average power of 600W. The investigation of single pulse laser drilling in this paper was based on theoretical and experimental solutions. In single pulse technique, the investigation included focal plane position fpp, pulse shape, laser peak power, and pulse duration. It was found that (-1) was the best fpp due to less taper for the drilled holes made by this level (Entrance hole =0.68, Exit hole = 0.27). To predict pulse shape effects; three types were : rectangular , rump-up and cool down, it were examined found that rectangular pulse was efficient more than the other types due to its ability to produce holes with less tapering as compared with others types. Also its found that all pulse shapes had the same effect on the materials microstructure . Laser peak power and pulse duration had the predominant affects on the hole dimensions and edge quality without any defect except hole tapering.

عملية التثقيب بالليزر لها القدرة على إنتاج ثقوب صغيرة، عالية الدقة . في هذا البحث استخدم ليزر النيدميوم- ياك النبضي بالملي ثانية لدراسة تغير خصائص الليزر على أبعاد الثقوب وعلى البنية المجهرية لعينات المادة المركبة ( المادة الأساس والألياف ) بسمك 2 مليمتر عند تثقيبها باستخدام تقنية النبضة المفردة . نوع الليزر المستخدم كان GSI lumonics JK760TR بطول موجي 0.3-50 ملي ثانية بمعدل قدرة 600 واط وأعلى مستوى تردد يصل الى 500 هيرتز. في حالة النبضة المفردة فان خصائص الليزر التي تم تغييرها هي موقع المستوى البؤري,وشكل النبضة، وقدرة النبضة، وطول النبضة ولقد وجد انه في حالة التثقيب بالنبضة المفردة فان افضل مستوى للتثقيب هو (-1) من بين اربع مستويات تم استخدامها وهي بالتسلسل (+1 ، 0 ، -1، -2 ) وذلك لاعطائه ثقوب اقل استدقاقا مقارنة بالمستويات الاخرى حيث كان قطر الثقب في منطقة الدخول = 0.86 اما في نقطة الخروج فكان = 0.27. لاختبار تأثير شكل النبضة، فقد استخدمت ثلاث اشكال وتم ملاحظة أن النبضة المستطيلة أكثر كفاءة وذلك لقابليتها على إنتاج ثقوب اقل استدقاقا مقارنة بالأشكال الأخرى اما تأثيرها على البنية المجهرية للمادة فكان متشابها. إن طاقة الليزر ومدة النبضة لها التأثير السائد على أبعاد وحجم الثقوب وكذلك على المنطقة المتأثرة بالحرارة بدون أي عيوب ماعدا استدقاق الثقب الذي كان صفة ملازمة لكل الثقوب التي أجريت بهذه الطريقة .} }