@Article{, title={EFFECT OF BLANK HOLDER TYPE ON DEEP DRAWING OF CUPS تأثير نوع ماسك الغقل في عملية السحب العميق}, author={Dr. Karem M, Younis}, journal={Iraqi journal of mechanical and material engineering المجلة العراقية للهندسة الميكانيكية وهندسة المواد}, volume={13}, number={1}, pages={106-119}, year={2013}, abstract={The purpose of this study is to examine the change in the wall thickness of drawn cup by using fixed blank holder gap (BHG) and variable blank holder force (BHF) to hold the sheets metal during drawing operations. The effect of BHG and BHF on drawn cups was studied by the experimental and theoretical approach. Two blank holder gap, BHG = 0.5, and 1 mm and variable blank holder force were used in the experiments. The study shows that a type of blank holder has a great effect on the quality change of the wall thickness of the final product, and BHG and BHF are considered important parameter to control material flow. Punch and die with diameters 43mm, 44 mm respectively are used to draw low carbon steel sheet (1008-AISI) with a thickness of 0.5 mm to draw a (cylindrical cups) from blanks with different reductions 0.5,0.55, 0.6, 0.65, and 0.7. The punch and die have the profile radius 4mm. Press with a maximum load capacity of 200 KN with speed 10 mm/mint was used to perform this research. The results show that no change occurs in the thickness of cups at ρ = 0.6 R, radius of blank, whereas the maximum change (thickening) of the wall thickness occurs when ρ = R, and the minimum value (thinning) of wall thickness in the corner of the cup. All values which estimated theoretically are slightly different for measured experimentally. The best results were obtained from the BHG = 0.5 mm compare to BHG = 1mm and BHF.

ألغرض من هذه الدراسة هو الكشف عن التغير في سمك جدار الوعاءالمسحوب باستخدام ماسك الغفل ذو الفجوة الثابتةBHG و استخدام نابض متغيرالقوة BHF لمسك الغفل المأخود من صفيحة معدنية خلال عمليات السحب. تمت دراسة تاثيرBHF وBHG لوعاء دائري عمليا ونظريا من خلال فجوتان1ملم و0.5ملم , و BHFمتغير القوة. بينت الدراسة ان نوع ماسك الغفل له تاثيرا كبيرا على نوعية التشكيل للجزء النهائي حيث يعتبر BHF وBHG من الوسائل المهمة للسيطرة على انسياب المعدن. يتألف قالب السحب الذي تم تنفيذ العمل به من خرامة و فتحة سحب بأقطار 43و 44 ملم على التوالى لسحب اوعية اسطوانية من اغفال مأخودة من صفائح الصلب المنخفض الكربون (1008-AISI) وبسمك 0.5 ملم بمختلف التخصرات, 0.50.55, 0.7,0.65,0.6 وأن انصاف اقطار تقوس القالب هي 4 ملم (للخرامة و لفتحة السحب).السعة الكلية للمكبس المستخدم لتنفيذ الاختبارات هى 200كيلو نيوتن و بسرعة 10ملم/دقيقة.بينت االنتائج عدم تغير سمك المنتج عند مسافةρ=0.6Rبينما اكبرتغير في السمك (تضخم) يحصل عند مسافةρ=R وأن اقل قيمة للترقق في سمك الجدار تحصل عند اركان الوعاء السفلية. اغلب القيم المخمنة نظريا تختلف بشكل طفيف عن القيم المقاسة عمليا.افضل النتائج تم الحصول عليها باستخدام فجوة ماسك الغفل الثابت (BHG) مقدارها (0.5 mm) بالمقارنة مع الماسكين الاخرين واللذين هما ماسك الغفل (BHG) ذو الفجوةالثابته التي مقدارها (1mm) وماسك الغفل المتغيرالقوة (BHF).} }