@Article{, title={Study the effect of adding oyster shells powder extracted from the Caspian Sea on the Mechanical Properties of Low Density of Polyethylene (LDPE). دراسة تأثير إضافة مسحوق قشور المحار المستخرج من بحر قزوين على الخواص الميكانيكيه للبولي اثيلين واطئ الكثافة (LDPE)}, author={Ahmed J. Mohammed أحمد جاسم محمد}, journal={Journal of Basrah Researches (Sciences) مجلة ابحاث البصرة ( العلميات)}, volume={39}, number={4B}, pages={46-56}, year={2013}, abstract={The Study of the Effect of from the Caspian Sea on the of low density polyethylene (LDPE), which is manufactured in the General state company of petrochemical industries, Basra, as function of the percentages of oysters extracted from the Caspian Sea in Iran (2.5%,5%,10%, 15%, 20% ), at particular size. ( 250 m) were investigated through several variables, such as, Young's modules, strength, and elongation. The obtained results were appeared that the added oyster act to reduce the spaces between the polymer chains, which reflects the high ability of the polymer against the applied stress, and a high degree of homogeneity between the host polymer and the added fillers, and this increase will give further property that increase the hardness of the prepared specimens, the results lead to that the strength at both break will be affected little till the percentage (2.5%), and lowered after that with increasing the percentage also indicate an lowered in young's modules at the percentage (10%), which reflects the increase in the ductile of the polymer grafted with eggshells and wide range of the application for this polymer. The results also appear that the highest point of the stress is (10.15 N/mm2 ). The proportional limit was 143 N for 5%.

تم في هذا البحث دراسة الخواص الميكانيكية لبوليمر الاثيلين واطئ الكثافة LDPE والمصنع في معمل بتروكيمياويات البصره كداله للنسبة الوزنية لمسحوق قشور المحار المستخرج من بحر قزوين في إيران(0%,2.5%,5%,10%,15%,20%) وعند حجم دقيقه أما اقل أو مساو إلى (250 m)إذ تمت دراسة عدة متغيرات مثل الاستطالة وقوه الشد عند الوهن والقطع ومعامل يونك وبينت النتائج المستحصله ان المحار المضاف يعمل على تقليل الفراغات بين السلاسل البوليمريه مما يعكس إمكانية البوليمر العالية بتحمل الإجهاد المسلط عليه وتكون درجة التجانس عالية بين كل من البوليمر والحشوات ، وان زيادة نسبة المالئات تضفي زيادة صفة الصلابة على النماذج المحضرة عند النسبة المئوية (%5)،ودللت النتائج إن سلوك قوة الشد عند القطع يكون ذا تأثير عند النسبة (% 2.5) من المضاف بعدها تهبط بزيادة كمية المضاف إذ تكون لحشوات المحار كمواد مالئة تأثير على خصائص البولي اثيلين والذي له خصائص ميكانيكية ضعيفة لذلك تنخفض قوة الشد عند القطع ويلاحظ ايضا انخفاض معامل يونك مع نسبه المضاف (%10) مما يعكس مرونة البوليمر المطعم بالمحار وتوسع مدى التطبيقات لهذا البوليمر وبينت النتائج ان أعلى نقطه للإجهاد هي) .15 N/mm210)،وكانت أعلى قيمة لحد التناسب (proportional limit) 143 N للنسبة الوزنية %5.} }