TY - JOUR ID - TI - Hydraulic Characteristics of Flow Over Rectangular Weir With Three Rectangular Bottom Openings Using ANN AU - Nassrin J.Al-Mansori AU - Jabbar.H.Al-Baidhani AU - Rafa.H.Al-Suhaili PY - 2014 VL - 22 IS - 4 SP - 951 EP - 962 JO - Journal of University of Babylon مجلة جامعة بابل SN - 19920652 23128135 AB - This research was based on laboratory experiments for hydraulic characteristics for a rectangular weir with three rectangular bottom openings (equal size of openings, different size of mid opening than an equal size sides opening. fifty-six physical models were made for this structure with different geometrical dimensions. Data set are analyzed in order to find the discharge coefficient for three flow cases when water level (under openings height or between openings height and under crest level and finally through openings and over the weir) and this analysis is done by using an equation prepared for each flow. Dimensional analysis was made to relate the discharge coefficient with different geometrical and flow variables for each flow cases . The highest value of the discharge coefficient, was obtained for flow case no.3, (Cdc = 0.462), while the lowest value of discharge coefficient was occurred for flow case no.1,(Cdp =0.0193). The correlation of (Cdp , Cdf , Cdc)was higher negative with (bo/H) with values of (-0.706,-0.937,-0.863) respectively.For all the cases tested the coefficient of variation for the discharge coefficient were of range values (0.5632 - 0.211) which indicate the necessity of obtaining a model to describe this variation. An ANN models was developed herein using (SPSS software) to express the discharge coefficient as a function of the different geometrical and flow variables, with range of correlation coefficient for all models (r=0.999 - 0.941) and applied the results in VISUAL Studio Net,2010 in order to be used by Engineers to find the discharge coefficient and the actual discharge of each model.

تم في هذا البحث اعتماد التجارب المختبرية لدراسة الخواص الهيدروليكية للهدار نوع مستطيل مع وجود ثلاث فتحات مستطيلة الشکل فی اسفله،(متساوية الابعاد مرة ومختلفة الابعاد للفتحة الوسطية مقارنة بأبعاد الفتحتين الجانبيتين مرة اخرى. تم عمل (56) نموذج مختلف من هذا المنشأ بأختلاف الابعاد لکل من الهدار والفتحات لكل نموذج. حيث تم أجراء التجارب لکل النماذج مع قيم مختلفة للجريان بضوء ما تسمح به المنظومة المختبرية .لکل نموذج من النماذج أعلاه، تم تحلیل القراءات لغرض ايجاد معامل التصريف لثلاث حالات من الجريان لمستوى الماء (تحت منسوب الفتحات, بين منسوب أعلى الفتحات وأسفل حافة الهدار والحالة الاخيرة للجريان من الفتحات واعلى الهدار) باستخدام معادلة اشتقت لكل حالة من حالات الجريان. تم إجراء تحليل بعدی لأيجاد علاقة لا بعدية بين معامل التصريف و متغيرات تمثل إبعاد النموذج وأخرى تمثل الجريان لكل حالة من الحالات السابقة الذكر . وان اعلى قيمة لمعامل التصريف كان للحالة الثالثة بقيمة (Cdc = 0.462) واقل قيمة لمعامل التصريف كانت للحالة الاولى بقيمة(Cdp =0.0193).واعلى قيمة ارتباط لكل قيم معامل التصريف للحالات الثلاثة كانت مع (bo/H) بقيم(-0.706,-0.937,-0.863) على التوالي وان معامل التغيير لكل حالات الجريان كانت تتراوح بين (0.5632-0.211) مما يؤكد ضرورة عمل النماذج لوصف حالة التغيير.يقوم نموذج ( ANN ) بأيجاد معامل التصريف كدالة لمختلف المتغيرات المتعلقة بالابعاد الهندسية الخاصة بالنموذج والمتغيرات التي تمثل الجريان بقيم معامل ارتباط لكل الشبکات يتراوح بين (r=0.999-0.941) والذی يصنف قويآ ضمن مقاييس الارتباط کما تم بناء نموذج (Visual Studio Net,2010) لغة بيسك المرئية سهلة التطبيق لغرض استخدامه من قبل مهندسین لأيجاد معامل التصريف والتصريف الحقيقي لجميع النماذج. ER -