Table of content

Engineering and Technology Journal

مجلة الهندسة والتكنولوجيا

ISSN: 16816900 24120758
Publisher: University of Technology
Faculty: Presidency of the university or centers
Language: Arabic and English

This journal is Open Access

About

The Journal aims to disseminate knowledge in the fields of Engineering, Technology and Sciences .All the researches will submit to the scientific evaluation procedures of publishing and documentation. The journal under takes only the publishing of the new researches that had not been published previously on other journals or debated in conferences.

The Instructions of Submitting The Research to Scientific Evaluation:
a- The research should be Submitted in 4 copies in Arabic or English Languages, auther's name should be eliminated from 2 copies only. The abstract should be typed on the front page not exceeding (150 words) in both Arabic and English on size (A4) sheet. Pages should be numbered and not more than (15) page.
b- The researcher should fill a declaration form which states that he doesn't publish the research during the evaluation period. He must give his full address phone number and e-mail.

Firstly- The author should pay a fee of (ID55000) when he submits the research and a fee of (ID55000) when the research is accepted .These fees are obligatory for all. The sum cannot be reimbursed in any case.
Secondly- The annual subscription in the journal inside Iraq is ID250000) Iraqi dinar, and outside Iraq is (us $250) abroad.
____________________________________________
____________________________________________
Engineering and Technology Journal
Publication Ethics
The publication of science and technology include thorough, methodical and complete processes by publishers and editors which have to be handled efficiently and proficiently. To sustain high ethical values of publication, publishers attempt to work intimately at all times with editors, authors, and peer-reviewers. The ethics statement for the Engineering & Technology Journal is based on those issued by the Committee on Publication Ethics (COPE) Code of Conduct guidelines available at www.publicationethics.org. The basic publishing ethics involved in the publishing process can be summarized as follows:

Reviewers’ Responsibilities
The responsibilities of the reviewers can be identified as:
• To provide a detailed, effective, and unbiased evaluation in promptly on the scientific content of the work.
• To indicate whether the writing is relevant, brief and clear and evaluating the originality and scientific accuracy of the submitted paper.
• To maintain the confidentiality of the complete review process.
• To inform the journal editor about any financial or personal conflict of interest and reject to review the manuscript when a possibility of such a conflict exists.
• To inform the journal editor of any ethical concerns in their evaluation of submitted manuscripts; such as any violation of ethical treatment of animal or human subjects or any considerable similarity between the previously published article and any reviewed manuscript.

Authors’ Responsibilities
The responsibilities of the authors can be described as:
• To assure that all the work reported in the manuscript must be original and free from any plagiarism.
• To make confident that the submitted work should not have been published elsewhere or submitted to any other journal(s) at the same time.
• To explicitly acknowledge any potential conflict of interest.
• The author(s) must give proper acknowledgments to other work reported (individual/company/institution). Permission must be obtained from any content used from other sources.
• It is important to note that only those who have made any substantial contribution to the interpretation or composition of the submitted work should be listed as ‘Authors’. On the other hand, other contributors should be mentioned as ‘co-authors’.

Publishers’ Responsibilities
The responsibilities of the Engineering & Technology Journal can be defined as:
• Engineering & Technology Journal is committed to working with journal editors, defining clearly their relevant roles, in order to ensure appropriate decisions regarding publication procedures and maintaining the transparency of editorial decisions.
• Engineering & Technology Journal guarantees the integrity autonomy and originality of each published article concerning:
o publication and research funding
o publication ethics and integrity
o conflicts of interest
o confidentiality
o authorship
o article modifications
o timely release of content.
____________________________________________
____________________________________________

ENGINEERING AND TECHNOLOGY JOURNAL
Scientific Refereed Journal Issued by University of Technology, IRAQ
COPYRIGHT AGREEMENT

The following assignment of copyright, executed and signed by the Author, is required with each manuscript submission. If the article is a “work made for hire”, the employer must sign it. The Author warrants that he/she has full power to make this agreement on behalf of himself and all his co-authors.
To the extent transferable, copyright in and of the undersigned, Author’s article titled:
************************************************************************by: *************************************************Reference ID: ******* submitted to the Engineering and Technology Journal is hereby assigned for publication.
In consideration of the acceptance of the Article for publication, the Author assigns to the Journal with full title guarantee, all copyrights, rights in the nature of copyright, and all other intellectual property rights in the Article throughout the world (present and future, and including all renewals, extensions, revivals, restorations and accrued rights of action).
The Author represents that he is the author and proprietor of this Article and that this Article has not heretofore been published in any form. The Author warrants that he has obtained written permission and paid all fees for use of any literary or illustration material for which rights are held by others. The Author agrees to hold the Editor(s)/Publisher harmless against any suit, demand, claim or recovery, finally sustained, by reason of any violation of proprietary right or copyright, or any unlawful matter contained in this article:



Signature: Date:
Name of Author:
Institution or Company:

Loading...
Contact info

جمهورية العراق –بغداد
الجامعة التكنولوجية- مجلة الهندسة والتكنولوجيا- ص.ب. 35010
Email: etj@uotechnology.edu.iq
____________________________________________
Journal website:
http://uotechnology.edu.iq/tec_magaz/EN/index.htm
____________________________________________
Republic of Iraq, Baghdad
University of Technology, Engineering & Technology Journal.
P.O.Box.35010
Email: etj@uotechnology.edu.iq

Email: uot_magaz@yahoo.com
__________________________________________
__________________________________________

Google Scholar Citations:
________________________
https://scholar.google.com/citations?user=w1aCAoMAAAAJ&hl=en

Table of content: 2018 volume:36 issue:9 Part (A) Engineering

Article
Synthesis and Characterization Nano Structure of MnO2 via Chemical Method

Authors: Khitam S. Shaker --- Alyaa H. AbdAlsalm
Pages: 946-950
Loading...
Loading...
Abstract

In the current research, Magnesium oxide II (MnO2) nanostructures were prepared by chemical route from hydro manganese chloride salt using Potassium hydroxide as reducing agent. X-Ray diffraction (XRD), SEM and Fourier transformation infrared (FTIR) used to characterize both particle size and structure of MnO2 nanoparticles. XRD results confirmed impurity of synthesized powder with α-MnO2 as predominant phase. The average particle size of manganese dioxide was in the range 25- 30 nm. Photographs of scanning electron microscope (SEM) showed two hierarchical structures, cluster agglomeration and chain appearance.


Article
A Mixture between Rule 90 and Rule 150 Cellular Automata as a Test Pattern Generator

Authors: Sahar Z. Alawey
Pages: 951-956
Loading...
Loading...
Abstract

Built-in Self-test (BIST) is one of integrated circuit (IC) testing techniques that can be used as a pseudo-random generator for the Circuit Under Test (CUT). This paper introduces the design and simulation of a 4-bit test pattern generator (TPG) using a one dimension Linear Hybrid Cellular Automata (LHCA) with a mixture of rule 90 and 150. LHCA is an enhancement from Linear Feedback Shift Register (LFSR) which can have more random test vectors and improving the cycle length. Design and simulation have been performed using Quartus II and Model Sim software.


Article
Investigation of Addition Different Fibers on the Performance of Cement Mortar

Loading...
Loading...
Abstract

This work presents an investigation of possibility incorporate of synthetic fibers (glass, nylon and carbon) at two states (short: 1cm, long: 5cm) effects on the mechanical properties of mortars (cement: sand composition (1:3)). Fibers materials used at different weight percentages ranged of (0, 0.4, 0.8, and 1.2) wt%. Density, water absorption, porosity, thermal conductivity, compressive strength and flexural strength experimentally investigated for mortar specimens after curing for (28 days). The results showed that the incorporation of these fiber materials improvement mechanical and physical tests for all reinforced samples with short and long fibers, and that the highest value of the mechanical and physical properties obtained from long fiber (5cm) reinforced cement samples with (1.2%Nylon), reaching the rate of increase in values of compressive strength by (17.74%), flexural strength by (52.8%), and water absorption by (4.54%), while reaching the rate of decrease in values of density by (5.32%). The higher values for short fiber (1cm) reinforced samples reaching the rate of increase in values of compressive strength by (10.92%), flexural strength by (40.65%), and water absorption by (6.65%), while reaching the rate of decrease in values of density by (8.91%). Results of thermal conductivity test showed decrease in values conductivity for all mortar samples with long short synthetic fibers and that the minimum value of conductivity obtained with (1.2%Carbon), reaching the rate of increase in values of thermal conductivity by (41.84%) for long fiber reinforced samples, while the lowest value for conductivity by (75.98%) for short fiber reinforced samples.


Article
Realization of Direct Linear Relation Between Control Voltage and Resonance Frequency of the LC Voltage Controlled Oscillator

Authors: Azzad B. Saeed
Pages: 966-971
Loading...
Loading...
Abstract

The main problem of traditional LC ( L represents the inductance, and C represents the Capacitance) Voltage Controlled Oscillators VCOs, is the non-linearity relation between the tuning control voltage and output resonance frequency, which is caused by two following reasons: the first one is the inverse and non-linear relation between the tuning control voltage and produced capacitance of the used varactor diode in the VCO circuit, and the second is the inverse and non-linear relation between the capacitance value of the used varactor diode and the output resonance frequency. In this paper, a proposed circuit has been designed and implemented to solve this problem and realize a direct-linear relation between the tuning control voltage and output resonance frequency for the LC Voltage Controlled Oscillator that utilize the varactor diode as a voltage controlled capacitance. The proposed circuit has been realized using Logarithmic, Inverting, Ant-Logarithmic, and Difference Amplifiers, which they are characterized by their simplicity and low cost. The theoretical and practical results of testing the proposed circuit had been presented using MATLAB software package. The proposed work has been practically tested by 21 measurement points, whereas, it has exhibited stimulant results that supports the successfulness of its design and performance.


Article
Mechanical and Acoustic Properties of Composite Material in a Secondary Roof to Reducing the Cooling Load

Loading...
Loading...
Abstract

The present investigation aims to perform experimental study to show the feasibility of application composite materials as secondary roofs, as well as their capability for reducing cooling load in building. Moreover, compare some of their mechanical properties and acoustic insulation with conventional secondary roofs. Three basic models, which are common, were chosen for the construction of buildings' roofs in Baghdad (concrete and concrete tiles as basic components of the first model, brick and clay tiles as basic components of the second model and brick and normal tiles as basic components of the third model). In addition, three composite materials were used in present work (fiber glass+ Nylon 66, fiber glass+ one layer of date palm cortex and fiber glass+ two layers of date palm cortex). The gypsum plates have been selected as a conventional secondary roofs when performing calculations and comparison. The results show that using proposed composite materials leads to significant reduction in cooling load by about 69.56 %, 65.3 % and 65.5 % respectively for the three models. In addition, the comparison of acoustic insulation shows that the proposed materials offer good acoustic insulation. Moreover, these materials able to afford external shocks better.


Article
Grasping Force Controlling by Slip Detection for Specific Artificial Hand (ottobock 8E37)

Loading...
Loading...
Abstract

This paper presents a theoretical and experimental study to control grasping force of specific artificial hand (Otto Bock 8E37), which it uses by amputees. The hand has two rigid fingers actuated by a DC motor through a multi-gears system. The aim of this work is to give the amputees a feeling of slipping while the hand grasping an object. The mathematical model has been derived to simulate the hand mechanism and analyze the generated signal of contact force between fingertip and the grasped object through a slippage phenomenon. The experimental work consisted of modifying the artificial hand design to aid load cell mounting process in order to measure the grasping force indirectly, then acquiring the measured signal to the PC. An artificial neural network (ANN) was trained on the patterns of the force signals. These patterns were prepared by using force sensors with modified design of the artificial hand for detecting the slippage of the different shapes grasped object. The Neural Network training results have been evaluated and discussed under different conditions, which affect the controller operation such as network error, classification percentage and the response time delay.


Article
Effect of Friction Stir Processing (FSP) to the Some Properties of Pure Copper Welded by Friction Stir Welding

Authors: Mais A. abdulkareem
Pages: 985-990
Loading...
Loading...
Abstract

Friction stir processing (FSP) is an innovative technique of varying the metallic features by intense, local plastic deforming. Accordingly, materials are stirred with no altering the phase via melting or otherwise to produce a microstructure with equiaxed and fine grains. This method enhances the microstructural features of metals. In This study the microstructure and the mechanical features including (tensile strength and microhardness), and radiographic inspection results are studied. All specimens of pure copper use in the (FSW) and (FSP) have variable rotating speed (900, 1200, and 1600 rpm) with constant feed speed (40 mm/min). The most remarkable results, the ultimate tensile strength for FSW and FSP at (1200 RPM and 40 mm/min) with the values of 250.4 MPa for FSW and 261..2 MPa for FSP and the efficiency reached 92.7% and 96.3% for FSP and FSW, respectively. The high hardness in the same sample was 118 HV for FSW and 135 HV for FSP. The microstructure at welding zones, specially nugget zone, is improved by the friction stir processing. Radiographic examination showed incomplete fusion of welding joint without defect.


Article
Investigation and Analysis of Force Production Mechanism for Partitioned Stator Flux Reversal Permanent Magnet Linear Machine

Authors: Ahlam L. Shuraiji --- Zi Qiang Zhu
Pages: 991-996
Loading...
Loading...
Abstract

In this paper, the force production mechanism in partitioned stator flux reversal permanent magnet (PS-FRPM) linear machine will be investigated. Since the PS-FRPM linear machine has both armature windings and the permanent magnet (PM) in one machine part and the other part is passive; thereby, the force production mechanism in conventional PM linear machine, is not valid for such a machine. In order to determine both magnetic and electrical loading frequency components, which result in production the electromagnetic force a spatial harmonic analysis is adapted. It has been found that the electromagnetic force in the PS-FRPM linear machine is produced by the interaction of the fundamental and its non-triple multiples harmonic orders of the stator winding magneto-motive force (MMF) with the air gap flux density, which is equal to the product of the PM (MMF) and the air gap permeance accounting for both the mover pole and the upper stator teeth. The analytical results are validated by finite element analysis (FEA), which are shown good agreement.


Article
A Compact Dual-Band BPF Based on Open Loop Resonator for Satellite Communication Applications

Authors: Ali J. Salim --- Aya N. Alkhafaji --- Mushtaq A. Alqaisy
Pages: 997-1001
Loading...
Loading...
Abstract

In this paper, a new filter is constructed by inserting two slots in the form of rectangular open loop resonator with folded ends. The insertion of these slots has successfully led to the compact size and the dual bandwidth behavior. The overall filter dimensions are 16×12 mm2, which correspond to 0.61λg × 0.4λg using a substrate with Rogers Ro 4003 with a relative permittivity of 3.38 and thickness of 1.0 mm. The resulting structure exhibits a dual-band behavior. The first passband has a center frequency of 6.2 GHz with FBW of 16.833% and input reflection coefficient better than -30 dB and insertion loss is approximately equal to -0.3 dB. In the second passband, the center frequency is 9.6 GHz, and the FBW is 12.57% with an input reflection coefficient better than -25 dB and insertion loss is approximately equal to -0.5 dB. The transmission zero is located between the dual passbands at 7.8 GHz with over -28.66 dB of the stopband. The simulation and performance evaluation of the proposed filter have been carried out using Microwave Studio Suite of Computer Simulation Technology (CST). As a result, this makes the proposed filter candidate for operating in satellite applications.


Article
Energy Saving in Power Consumption by Using Double Glazing Windows in Iraq

Authors: Walaa M. Hashim --- Hisham A. Hoshi
Pages: 1002-1007
Loading...
Loading...
Abstract

It is generally accepted that the summer in Iraq is relatively hot season, where the temperature sometimes reaches 60 Cº. Accordingly, most of the Iraqi houses are characterized as having a large area of windows with a single glass, which could be resulted in a significant loss in cooling energy. Hence, the present research concern is to examine the effect of using double glass windows (as an alternative to single glass) on the saving in which energy normally used in houses and buildings at July and August for different hours 3, 6, 9, 12, 15, 18, 21 and 24 P.m. A practical and realistic study was conducted. Three values of aspect ratio are used 30, 15 and 10 for the presence of air between the panels and in the presence of the argon gas for aspect ratio, 10 were practically investigated. The experimental results confirmed that using of the double glass with the presence of air as a medium for heat transfer between the two panels could be reduced the amount of heat transferred compared to that of single glass between (45-78), (54-85)and(58-88)%, while for argon it was (60-91)%.


Article
Biosorption Technique for Naphthalene Removal from Aqueous Solution By Chara sp., Algae

Authors: Talib M. Albayati --- Khairi R. Kalash
Pages: 1008-1015
Loading...
Loading...
Abstract

These instructions give guidelines for preparing the article to be published in the Engineering& Technology Journal using MS World 7.0 or later. A short abstract should open the paper and give a clear indication of the aims, scope and the main results of the paper. The reader may decide from the abstract that the full text is of particular interest or not. The author should consider that the abstract is an indication of the scope of the topic and the obtained results and not a way of condensing the problem in a few words for quick reading. It should be no more than 200 words. It is placed under the title with a single space from the title. The paper titles should be concise and definitive. The length of the title should not exceed three lines. The abbreviations and formulae should be avoided. Papers titles should be written in uppercase and lowercase letters, not all uppercase. Capitalize the words of the paper title. Avoid writing a long formula and define all symbols used in the abstract and do not cite the references here.


Article
Design and Performance Analysis of Contact Lens Materials for Chromatic and Polychromatic Aberrations Correction

Authors: Ali H. Al-Hamdani
Pages: 1016-1021
Loading...
Loading...
Abstract

A material scientists worldwide has investigated optical plastics as alternative materials for glasses that have been widely used over the years. Plastics have numerous advantages over glasses in optical applications, especially in ophthalmic applications. Recently, researchers have developed new polymer materials to satisfy the ophthalmic industry requirements. Mechanical, chemical and physical tests were conducted to determine the polymers for contact lenses. In this study, the optical properties of polymers were evaluated and analyzed by using Zemax program depending on Liou & Brennan model. The effect of achromatic and polychromatic light on the performance of the polymers contact lenses was investigated. The modulation transfer function (MTF) and root mean square spot size (RMS) were the two criteria for analyzing the results and determining the effect of chromatic aberration on different polymers contact lens performances.

Table of content: volume:36 issue:9 Part (A) Engineering